ADG419BNZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | ADG419 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Operating Supply Voltage | 12V |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 5V |
| Power Dissipation | 35μW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 160 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 160 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 13.5V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| Switch Circuit | SPDT |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 25mOhm |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 3.43mm |
| Length | 9.27mm |
| Width | 7.24mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG419BNZ Overview
Shipping overseas is convenient due to the electrical component's packing in 8-DIP (0.300, 7.62mm). In order to provide high reliability, an advanced packaging method Tube is used. In Through Hole, you'll find this switch device. Multiplexers and demultiplexers have the same number of circuits 2:1. Temperatures around -40°C~125°C TA are extended for operation. In total, 8 terminations have occurred. By its 1 channels, the electronic component provides high-quality output. A 15V voltage supply should turn on and run the electronic component. Into the electrical component body are injected 8 pins. Multiplexers built on a SPDT switching circuit are built. If you are looking for variants of the digital switch, trying search with ADG419. Analog switches have 35Ohm internal resistance. Datasheets for 8 pin functions are available upon request. This switch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 25V. A analog switch ic that has a cost-effective Dual, Single supply type. 5V is the lowest voltage the electrical component should receive. Putting voltage greater than 1μA on the multiplexer may cause damage. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. It is recommended that you attach at least 13.5V to your dual power supply. This electrical part is compatible with 12V operating voltages. This electronic component presents a Drain to Source resistance of 25mOhm. The analog switch ics includes 2 outputs.
ADG419BNZ Features
1 Channels
Switch Circuit: SPDT
Drain-to-Source resistance: 25mOhm
ADG419BNZ Applications
There are a lot of Analog Devices Inc. ADG419BNZ Analog Switches & Multiplexers ICs applications.
- Avionics test equipment
- USB 1.1 signal switching circuits
- Private Branch Exchange (PBX)
- PCMCIA cards
- Isolation
- High speed data transmission line cards
- Central office
- Transmit
- RGB switches
- Switching Systems
