ADG419BR
| Parameters | |
|---|---|
| Contact Plating | Lead, Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 235 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | ADG419 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Operating Supply Voltage | 12V |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 100pA |
| Power Dissipation | 35μW |
| Max Supply Current | 1μA |
| Propagation Delay | 160 ns |
| Turn On Delay Time | 160 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 160 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 13.5V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| Switch Circuit | SPDT |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 25Ohm |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG419BR Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-SOIC (0.154, 3.90mm Width). The advanced packaging method Tube provides high reliability. A switch device like this is mounted in Surface Mount. There is 2:1 ratio between the number of multiplexers and demultiplexers. Operational temperature extended around -40°C~125°C TA. 8 terminations have been made so far. By its 1 channels, the electronic component provides high-quality output. Turning on and running the electrical part should be easy with a 15V voltage supply. A total of 8 pins are injected into the body of the electronic part. On the other hand, analog switches can be constructed using SPDT switching circuits. Use ADG419 to search for variants of the digital switches. This digital multiplexer has 35Ohm internal resistance. To find out what the functions of 8 pins are, please refer to their datasheets. Theswitch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 25V volts for the multiplexer. An effective Dual, Single supply digital multiplexer. The lowest voltage the electronic part should receive is 5V. 100pA current would be enough for this multiplexer to operate. It may damage the digital multiplexer if the voltage is higher than 1μA. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 22V. It is recommended that you attach at least 13.5V to your dual power supply. Operating voltages range from 12V. Drain to Source resistance is 25Ohm. The analogue multiplexer has 2 outputs.
ADG419BR Features
1 Channels
Switch Circuit: SPDT
100pA Supply Current
Drain-to-Source resistance: 25Ohm
ADG419BR Applications
There are a lot of Analog Devices Inc. ADG419BR Analog Switches & Multiplexers ICs applications.
- Avionics and Military Systems
- Signal routing between systems
- USB 1.1 signal switching circuits
- DSUs
- ISDN NT1/TA
- Low-Voltage
- Cross Connects
- ATM
- SDH/SONET multiplexers
- Microwave transmission systems
