ADG419BR-REEL7
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 35μW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG419 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Operating Supply Voltage | 12V |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 100pA |
| Power Dissipation | 35μW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 160 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 160 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 13.5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| Switch Circuit | SPDT |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Dual (V±) | ±15V |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG419BR-REEL7 Overview
Shipping overseas is convenient due to the electrical component's packing in 8-SOIC (0.154, 3.90mm Width). High reliability is provided by advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexer and demultiplexer circuits have a number 2:1. Temperatures around -40°C~125°C TA are extended for operation. A total of 8 terminations have been recorded. By its 1 channels, the electronic component provides high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. It is injected into the electrical part body with 8 pins. Unlike digital switches, these are based on SPDT switching circuits. Try searching for ADG419 variants of the analog switch ic. Analog switches have 35Ohm internal resistance. The functions of 8 pins can be found in the datasheets. This switch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 25V. A cost-effective Dual, Single supply type analogue multiplexer. 5V is the lowest voltage that should be fed to the electronic electronic part. In order to operate this switch device, it would need a current of 100pA. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. If put voltage greater than 22V on the multiplexer, damage may be caused to the device. In the case of dual power supplies, you should connect at least 13.5V. There is a voltage range of 12V operating voltages for the electrical part. The analogue multiplexer has 2 outputs.
ADG419BR-REEL7 Features
1 Channels
Switch Circuit: SPDT
100pA Supply Current
ADG419BR-REEL7 Applications
There are a lot of Analog Devices Inc. ADG419BR-REEL7 Analog Switches & Multiplexers ICs applications.
- Microwave transmission systems
- MP3 players
- Video switching
- Remote wireless modules
- ISDN NT1/TA
- E1 Network Equipment
- High-Voltage
- Multiplexers
- Microprocessor Controlled Analog Systems
- HDTV
