ADG419BRM
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 35μW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 235 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | ADG419 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Operating Supply Voltage | 12V |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 5V |
| Power Dissipation | 35μW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 160 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 160 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 13.5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| Switch Circuit | SPDT |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Dual (V±) | ±15V |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG419BRM Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). High reliability is achieved by using advanced packaging method Tube. There is an analog multiplexer mounted in position Surface Mount. Multiplexer and demultiplexer circuits have a number 2:1. Operating temperature extended to -40°C~125°C TA. In total, there have been 8 terminations. A 1 channel electronic part produces high-quality output. A 15V voltage supply should turn on and run the electronic component. A total of 8 pins are injected into the electrical part body. Unlike digital switches, these are based on SPDT switching circuits. If you are looking for variants of the digital switch, trying search with ADG419. Internally, this switch multiplexer has a resistance of 35Ohm. Datasheets for 8 pin functions are available upon request. The analogue multiplexer in this example is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 25V. Dual, Single supply type digital switch with a low cost. A low voltage of 5V should be applied to the electronic component. Put voltage above 1μA on the multiplexer to cause damage. Despite this switch's dual supply capability, its voltage should not exceed 22V. The voltage should be at least 13.5V if you are using dual power supplies. Operating voltages range from 12V. 2 outputs are included in the analogue multiplexer.
ADG419BRM Features
1 Channels
Switch Circuit: SPDT
ADG419BRM Applications
There are a lot of Analog Devices Inc. ADG419BRM Analog Switches & Multiplexers ICs applications.
- Optical Applications
- E1 Multiplexer
- MP3 players
- DSLAMs
- PCMCIA cards
- Fault Tolerant Systems
- Audio signal routing
- Microprocessor Controlled Analog Systems
- New designs requiring multiplexer functions
- Digital cross connects (DSX-1)
