ADG419BRM-REEL
| Parameters | |
|---|---|
| Contact Plating | Lead, Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 35μW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG419 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Operating Supply Voltage | 12V |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 100pA |
| Power Dissipation | 35μW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 160 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 160 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 13.5V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| Switch Circuit | SPDT |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Dual (V±) | ±15V |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG419BRM-REEL Overview
Presented in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width), this electrical component is convenient for overseas shipping. High reliability is ensured by the advanced packaging method Tape & Reel (TR). In Surface Mount, you'll find this switch device. There is 2:1 ratio between the number of multiplexers and demultiplexers. Operating temperature around -40°C~125°C TA extended. Total terminations are 8. A high-quality output is provided by the electrical component's 1 channels. A 15V voltage supply should turn on and run the electronic component. The electronic part body is injected with 8 pins. On the other hand, analog switches can be constructed using SPDT switching circuits. Try searching with ADG419 to find analog multiplexer variants. Internally, this switch multiplexer has a resistance of 35Ohm. The datasheets for the 8 pins explain the functions. A analogue multiplexer of this type is a Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 25V. The analog switch ic is of the Dual, Single supply type and is cost-effective. The lowest voltage the electronic part should receive is 5V. The analogue multiplexer could operate on 100pA current. Put voltage above 1μA on the multiplexer to cause damage. Despite this switch device's dual supply capability, its voltage should not exceed 22V. When using dual power supplies, you should attach at least 13.5V. The electronic component can function from 12V. 2 outputs are included in the analogue multiplexer.
ADG419BRM-REEL Features
1 Channels
Switch Circuit: SPDT
100pA Supply Current
ADG419BRM-REEL Applications
There are a lot of Analog Devices Inc. ADG419BRM-REEL Analog Switches & Multiplexers ICs applications.
- Optical Applications
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Switching Systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Digital Cross-Connects
- Multi-Line E1 Interface Cards
- CSU
- RGB switches
- Battery Powered Instruments
- PCMCIA cards
