ADG419BRM-REEL7
| Parameters | |
|---|---|
| Switch Circuit | SPDT |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Dual (V±) | ±15V |
| Length | 4.9mm |
| Width | 3.9mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 35μW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG419 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 12V |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 100pA |
| Power Dissipation | 35μW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 160 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 160 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 13.5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
ADG419BRM-REEL7 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). The advanced packaging method Tape & Reel (TR) provides high reliability. There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have a ratio of 2:1. Operating temperature around -40°C~125°C TA extended. In total, there are 8 terminations. The electronic part delivers high-quality output through its 1 channels. An 15V voltage supply should allow the electrical part to be turned on and run. A total of 8 pins are injected into the body of the electronic part. These analog multiplexers are built based on SPDT switching circuits. ADG419 can be used to search for analog multiplexer variants. A 35Ohm internal resistance characterizes this multiplexer. The functions of 8 pins can be found in the datasheets. It is a typical Multiplexer or Switches analog multiplexer. In a normalsituation, users should not supply the switches with voltage higher than 25V. An effective Dual, Single supply digital multiplexer. The lowest voltage fed to the electronic component should be 5V. It would be sufficient to run this analogue multiplexer with 100pA current. A digital multiplexer may suffer damage if voltage is applied above 1μA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. If you are using a dual power supply, you should attach at least 13.5V. Operating voltages range from 12V. In this digital multiplexer, there are 2 outputs.
ADG419BRM-REEL7 Features
1 Channels
Switch Circuit: SPDT
100pA Supply Current
ADG419BRM-REEL7 Applications
There are a lot of Analog Devices Inc. ADG419BRM-REEL7 Analog Switches & Multiplexers ICs applications.
- Avionics test equipment
- Fiber In The Loop (FITL)
- Multiplexers
- Precision test equipment
- Relay Replacement
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Residential Gateways, Home Gateway/Router
- PDH Multiplexers
- Fiber to the Home
- Medical
