ADG419BRMZ-REEL
| Parameters | |
|---|---|
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| Switch Circuit | SPDT |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Dual (V±) | ±15V |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 35μW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG419 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Operating Supply Voltage | 12V |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 100pA |
| Power Dissipation | 35μW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 160 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 160 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 13.5V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
ADG419BRMZ-REEL Overview
The electronic component is convenient to ship overseas because it is packed in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). In Surface Mount, you'll find this switch device. 2:1 is the number of circuits in the multiplexer and demultiplexer. The operating temperature is extended to around -40°C~125°C TA. Total terminations are 8. This electronic part offers high-quality output due to its 1 channels. An 15V voltage supply should allow the electrical part to be turned on and run. Into the electrical component body are injected 8 pins. A SPDT switching circuit is used for these analog switches. Try searching for the analog switch ic with ADG419 if you are looking for variants. The internal resistance of this digital multiplexer is 35Ohm. To find out what the 8 pins do, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 25V. A cost-effective Dual, Single supply type analogue multiplexer. In order for the electronic part to function properly, the lowest voltage should be 5V. For this multiplexer to operate, 100pA current would be sufficient. It may damage the digital multiplexer if the voltage is higher than 1μA. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 22V. The voltage should be at least 13.5V if you are using dual power supplies. The electronic component can function from 12V. Multiplexer ics with 2 outputs are available.
ADG419BRMZ-REEL Features
1 Channels
Switch Circuit: SPDT
100pA Supply Current
ADG419BRMZ-REEL Applications
There are a lot of Analog Devices Inc. ADG419BRMZ-REEL Analog Switches & Multiplexers ICs applications.
- Battery-powered systems
- E1 Multiplexer
- Cross Connects
- Optical Applications
- Switching Systems
- E1 Network Equipment
- Communication systems
- Routers
- Digital Cross-Connects
- Imaging
