ADG419BRMZ-REEL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 35μW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG419 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Operating Supply Voltage | 12V |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 100pA |
| Power Dissipation | 35μW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 160 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 160 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 13.5V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| Switch Circuit | SPDT |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Dual (V±) | ±15V |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG419BRMZ-REEL7 Overview
Shipping overseas is convenient due to the electrical component's packing in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). Advanced packaging method Tape & Reel (TR) is used to provide high reliability. Surface Mount is where this multiplexer is located. 2:1 is the ratio between multiplexers and demultiplexers. An extended operating temperature of -40°C~125°C TA degrees Celsius. Total terminations are 8. This electronic part offers high-quality output due to its 1 channels. It is safe to turn on and run the electronic component with a 15V voltage supply. It is part of the design of the 8 series that this electronic component is included. These analog multiplexers are built based on SPDT switching circuits. ADG419 can be used to search for analog multiplexer variants. A 35Ohm internal resistance characterizes this multiplexer. To find out what the 8 pins do, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. Users should never supply a voltage higher than 25V to a switch device. Analog switch ics with Dual, Single supply type are cost-effective. It is recommended that the electrical component receives a voltage of 5V. 100pA current would be enough for this multiplexer to operate. When the digital multiplexer is charged above 1μA, damage can occur. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. For dual power supplies, a voltage of at least 13.5V should be attached. There is a voltage range of 12V operating voltages for the electrical part. A analog switch ics with 2 outputs is included.
ADG419BRMZ-REEL7 Features
1 Channels
Switch Circuit: SPDT
100pA Supply Current
ADG419BRMZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG419BRMZ-REEL7 Analog Switches & Multiplexers ICs applications.
- Signal routing between systems
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Audio and video routing
- Medical Instrumentation
- Cable PC
- PBXs
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Switching Systems
- Automotive applications
- Video switching
