ADG419BRZ

SPDT 35Ohm Analog Switches BREAK-BEFORE-MAKE ADG419 8 Pins 250pA 15V 8-SOIC (0.154, 3.90mm Width)

Manufacturer: Analog Devices Inc.
Nocochips NO: 84-ADG419BRZ
Package: 8-SOIC (0.154, 3.90mm Width)
Datasheet: PDF
Stock: 530
Description: SPDT 35Ohm Analog Switches BREAK-BEFORE-MAKE ADG419 8 Pins 250pA 15V 8-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	8
ECCN Code	EAR99
Resistance	35Ohm
Subcategory	Multiplexer or Switches
Max Power Dissipation	400mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	1
Supply Voltage	15V
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	ADG419
Pin Count	8
Number of Outputs	2
Operating Supply Voltage	12V
Polarity	Non-Inverting
Number of Channels	1
Interface	Parallel
Max Supply Voltage	25V
Min Supply Voltage	5V
Operating Supply Current	100pA
Power Dissipation	35μW
Max Supply Current	1μA
Propagation Delay	160 ns
Turn On Delay Time	160 ns
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	160 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	35Ohm
Min Dual Supply Voltage	13.5V
High Level Output Current	30mA
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	80 dB
Current - Leakage (IS(off)) (Max)	250pA
Channel Capacitance (CS(off), CD(off))	6pF
Switch Circuit	SPDT
Crosstalk	-90dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Drain to Source Resistance	25mOhm
Voltage - Supply, Dual (V±)	±15V
Height	1.5mm
Length	5mm
Width	4mm
Radiation Hardening	No
REACH SVHC	No SVHC
RoHS Status	ROHS3 Compliant
Lead Free	Contains Lead
Factory Lead Time	1 Week
Lifecycle Status	PRODUCTION (Last Updated: 1 month ago)
Contact Plating	Tin
Mounting Type	Surface Mount
Package / Case	8-SOIC (0.154, 3.90mm Width)
Surface Mount	YES
Number of Pins	8
Operating Temperature	-40°C~125°C TA
Packaging	Tube
JESD-609 Code	e3
Pbfree Code	no

ADG419BRZ Overview

Due to its 8-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. High reliability is ensured by the advanced packaging method Tube. Multiplexers like this are mounted in the Surface Mount position. 2:1 is the number of circuits in the multiplexer and demultiplexer. Around -40°C~125°C TA is the extended operating temperature. Total terminations are 8. A electrical component with 1 channels is capable of high-quality output. If the voltage supply is 15V volts, the electrical component should be turned on and run. This electronic part can be found in the 8 series. These analog multiplexers are built based on SPDT switching circuits. Try searching with ADG419 if you're looking for variants. It has an internal resistance of 35Ohm. Datasheets for functions of 8 pins are available. A analogue multiplexer of this type is a Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 25V. Analog switch ics with Dual, Single supply type are cost-effective. The lowest voltage the electronic part should receive is 5V. In order to operate this switch device, it would need a current of 100pA. A voltage higher than 1μA may cause damage to the switch multiplexer. Despite this switch's dual supply capability, its voltage should not exceed 22V. If you are using dual power supplies, you should attach at least 13.5V. This electrical part is compatible with 12V operating voltages. A Drain to Source resistance of 25mOhm is shown for this electronic part. The analog switch ics includes 2 outputs.