ADG419BRZ-REEL
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 35μW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG419 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Operating Supply Voltage | 12V |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 100pA |
| Power Dissipation | 35μW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 160 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 160 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 13.5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| Switch Circuit | SPDT |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Dual (V±) | ±15V |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG419BRZ-REEL Overview
Shipping overseas is convenient due to the electrical component's packing in 8-SOIC (0.154, 3.90mm Width). In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a number of circuits 2:1. Temperatures around -40°C~125°C TA are extended for operation. In total, 8 terminations have occurred. As a result of its 1 channels, this electronic component provides high-quality output. When a voltage supply of 15V is used, the electronic component should be turned on and run. This electrical component is included in the 8 series of products. Circuits based on SPDT switching are used to construct these analog switch ics. Search with ADG419 if you are looking for analog multiplexer variants. There is 35Ohm internal resistance in this digital multiplexer. You can find the functions of the 8 pins in the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. A voltage higher than 25V should not normally be supplied to the switches. The analog switch ic is of the Dual, Single supply type and is cost-effective. It is recommended to use 5V as the lowest voltage for the electrical part. This digital switch can be operated with a current of 100pA. The analogue multiplexer may be damaged if voltage is greater than 1μA. There is no problem with using dual supply voltage, but it should not exceed 22V. If you are using dual power supplies, you should attach at least 13.5V. The electronic component can function from 12V. The analogue multiplexer has 2 outputs.
ADG419BRZ-REEL Features
1 Channels
Switch Circuit: SPDT
100pA Supply Current
ADG419BRZ-REEL Applications
There are a lot of Analog Devices Inc. ADG419BRZ-REEL Analog Switches & Multiplexers ICs applications.
- New designs requiring multiplexer functions
- Signal routing between systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- ISDN NT1/TA
- Precision data acquisition
- Public switching systems
- Modems
- Mechanical reed relay replacement
- Digital Cross-Connects
- Ultrasound
