ADG419BRZ-REEL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 35μW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG419 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Operating Supply Voltage | 12V |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 100pA |
| Power Dissipation | 35μW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 160 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 160 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 13.5V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| Switch Circuit | SPDT |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Dual (V±) | ±15V |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG419BRZ-REEL7 Overview
Packed in 8-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. Surface Mount is where this multiplexer is located. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. Around -40°C~125°C TA is the extended operating temperature. In total, there are 8 terminations. Due to its 1 channels, the electrical component produces high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. An electrical component like this is included in the 8 series. A SPDT switching circuit is used to build these analog multiplexers. Try searching for ADG419 variants of the analog switch ic. In this multiplexer, the internal resistance is 35Ohm. The datasheets for the 8 pins explain the functions. The analog multiplexer shown here is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 25V to the switch device in normal circumstances. An effective Dual, Single supply digital multiplexer. 5V should be the lowest voltage fed to the electronic component. This multiplexer would work with 100pA current. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 22V. If you are using dual power supplies, you should attach at least 13.5V. Operating voltages range from 12V. A analog switch ics with 2 outputs is included.
ADG419BRZ-REEL7 Features
1 Channels
Switch Circuit: SPDT
100pA Supply Current
ADG419BRZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG419BRZ-REEL7 Analog Switches & Multiplexers ICs applications.
- RGB switches
- Intelligent PBX
- Communication systems
- DVD-R
- Avionics
- DSLAMs
- Switching Systems
- Fiber to the Home
- Wireless Local Loop
- Microwave transmission systems
