ADG419TQ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-CDIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Tin/Lead (Sn63Pb37) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 35μW |
| Technology | CMOS |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | ADG419 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Operating Supply Voltage | 12V |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 5V |
| Power Dissipation | 35μW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 160 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 160 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 13.5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| Switch Circuit | SPDT |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Dual (V±) | ±15V |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG419TQ Overview
The electronic component is convenient to ship overseas because it is packed in a 8-CDIP (0.300, 7.62mm). Advanced packaging method Tube is used to provide high reliability. Multiplexers like this are mounted in the Through Hole position. There is 2:1 ratio between the number of multiplexers and demultiplexers. The operating temperature is extended to around -55°C~125°C TA. Total terminations are 8. A electrical component with 1 channels is capable of high-quality output. A 15V voltage supply should turn on and run the electronic component. The electronic part body is injected with 8 pins. A SPDT switching circuit is used for these analog switches. Look for analog switch ic variants by searching with ADG419. There is 35Ohm internal resistance in this digital multiplexer. To find out what the 8 pins do, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 25V volts for the multiplexer. A analog switch ic that has a cost-effective Dual, Single supply type. 5V is the lowest voltage the electrical component should receive. It may damage the digital multiplexer if the voltage is higher than 1μA. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. A dual power supply should have at least 13.5V voltage attached. This electrical part is compatible with 12V operating voltages. This digital multiplexer has 2 outputs.
ADG419TQ Features
1 Channels
Switch Circuit: SPDT
ADG419TQ Applications
There are a lot of Analog Devices Inc. ADG419TQ Analog Switches & Multiplexers ICs applications.
- Avionics test equipment
- Frame Relay Equipment
- E1 Multiplexer
- SDH
- Precision instrumentation
- Audio and video switching
- Industrial and process control systems
- Video signal routing
- Channel Banks
- CSU
