ADG426BNZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 months ago) |
| Contact Plating | Tin |
| Mounting Type | Through Hole |
| Package / Case | 28-DIP (0.600, 15.24mm) |
| Surface Mount | NO |
| Number of Pins | 28 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| ECCN Code | EAR99 |
| Resistance | 80Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 3.1mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | NOT APPLICABLE |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | NOT APPLICABLE |
| Base Part Number | ADG426 |
| Pin Count | 28 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 12V |
| Number of Channels | 16 |
| Interface | Parallel |
| Number of Circuits | 1 |
| Max Supply Voltage | 25V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Nominal Supply Current | 100μA |
| Power Dissipation | 3.1mW |
| Supply Current-Max (Isup) | 0.5mA |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 110 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 80Ohm |
| High Level Output Current | 20mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 16:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 50pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Time (Ton, Toff) (Max) | 160ns, 150ns |
| Charge Injection | 8pC |
| Channel-to-Channel Matching (ΔRon) | 4 Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 80Ohm |
| Signal Current-Max | 0.02A |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 6.35mm |
| Length | 39.75mm |
| Width | 14.73mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG426BNZ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 28-DIP (0.600, 15.24mm). This high-reliability packaging method uses advanced packaging methods Tube. There is an analog multiplexer mounted in position Through Hole. Multiplexers and demultiplexers have a number of circuits 16:1. Temperatures around -40°C~85°C TA are extended for operation. Totally, there are 28 terminations. Due to its 16 channels, the electrical component produces high-quality output. If the voltage supply is 15V volts, the electrical component should be turned on and run. A total of 28 pins are injected into the electrical part body. This multiplexer is composed of 1 circuits. Using the ADG426 search parameter, you can discover variants of the switch. There is 80Ohm internal resistance in this digital multiplexer. Datasheets for 28 pin functions are available upon request. There is Multiplexer or Switches analog multiplexer like this in the world. In normalcircumstances, users should not exceed 25V volts for the multiplexer. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. Integrated with SINGLE-ENDED MULTIPLEXER analog IC. 12V operating voltages are supported by the electronic component. There is 80Ohm Drain to Source resistance on this electronic part.
ADG426BNZ Features
16 Channels
Drain-to-Source resistance: 80Ohm
ADG426BNZ Applications
There are a lot of Analog Devices Inc. ADG426BNZ Analog Switches & Multiplexers ICs applications.
- SONET
- Remote Powered Equipment
- Industrial and process control systems
- High-Voltage
- Microprocessor controlled systems
- Microwave transmission systems
- Cellular phones
- Battery Powered Systems
- ISDN NT1/TA
- Relay replacements
