ADG426BRS
| Parameters | |
|---|---|
| Max Supply Voltage | 25V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Operating Supply Current | 100μA |
| Nominal Supply Current | 100μA |
| Power Dissipation | 3.1mW |
| Max Supply Current | 200μA |
| Propagation Delay | 150 ns |
| Turn On Delay Time | 240 ns |
| Number of Inputs | 16 |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 110 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 80Ohm |
| High Level Output Current | 20mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 16:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 50pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Time (Ton, Toff) (Max) | 160ns, 150ns |
| Charge Injection | 8pC |
| Channel-to-Channel Matching (ΔRon) | 4 Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.02A |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 1.75mm |
| Length | 10.2mm |
| Width | 5.3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Contact Plating | Lead, Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 28-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 28 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| ECCN Code | EAR99 |
| Resistance | 80Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 3.1mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 235 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | ADG426 |
| Pin Count | 28 |
| Operating Supply Voltage | 12V |
| Number of Channels | 16 |
| Interface | Parallel |
| Number of Circuits | 1 |
ADG426BRS Overview
As the electronic part is packed in 28-SSOP (0.209, 5.30mm Width), international shipping is convenient. High reliability is ensured by the advanced packaging method Tube. This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have a number of circuits 16:1. Operation at a temperature around -40°C~85°C TA. A total of 28 terminations have been recorded. By its 16 channels, the electronic component provides high-quality output. When a voltage supply of 15V is used, the electronic component should be turned on and run. 28 pins are injected to the electronic part body. The circuits in this analogue multiplexer number 1. Try searching with ADG426 if you're looking for variants. It has an internal resistance of 80Ohm. Please refer to the datasheets for 28 pins functions. This switch device is a typical Multiplexer or Switches. Users shouldn't supply more than 25V voltage to the switch device. For this multiplexer to operate, 100μA current would be sufficient. A digital multiplexer may suffer damage if voltage is applied above 200μA. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 22V. An analog IC with the number SINGLE-ENDED MULTIPLEXER is integrated into this board. 12V operating voltages are supported by the electronic component. It is possible to operate 16 inputs.
ADG426BRS Features
16 Channels
100μA Supply Current
ADG426BRS Applications
There are a lot of Analog Devices Inc. ADG426BRS Analog Switches & Multiplexers ICs applications.
- Data switching
- DSUs
- 65 V DACs
- Cell phones
- Multiplexers
- Intelligent PBX
- Communications systems
- Power routing
- Digital Cross-Connects
- High-Voltage
