ADG426BRS-REEL7
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 28-SSOP (0.209, 5.30mm Width) |
| Surface Mount | YES |
| Number of Pins | 28 |
| Weight | 2.26799g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| ECCN Code | EAR99 |
| Resistance | 80Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 3.1mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG426 |
| Pin Count | 28 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 12V |
| Number of Channels | 16 |
| Interface | Parallel |
| Number of Circuits | 1 |
| Max Supply Voltage | 25V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Power Dissipation | 3.1mW |
| Supply Current-Max (Isup) | 0.5mA |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 110 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 80Ohm |
| Multiplexer/Demultiplexer Circuit | 16:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 50pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Time (Ton, Toff) (Max) | 160ns, 150ns |
| Charge Injection | 8pC |
| Channel-to-Channel Matching (ΔRon) | 4 Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.02A |
| Voltage - Supply, Dual (V±) | ±15V |
| Height Seated (Max) | 2mm |
| Width | 5.3mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG426BRS-REEL7 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 28-SSOP (0.209, 5.30mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have the same number of circuits 16:1. The operating temperature is extended to around -40°C~85°C TA. Total terminations are 28. A electrical component with 16 channels is capable of high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. The electrical component body receives 28 pins. The multiplexer consists of 1 circuits. ADG426 can be used to search for analog multiplexer variants. In this multiplexer, the internal resistance is 80Ohm. Datasheets for functions of 28 pins are available. A analogue multiplexer of this type is a Multiplexer or Switches. normally, users should not supply switches with voltages higher than 25V. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. An analog IC with the number SINGLE-ENDED MULTIPLEXER is integrated into this board. Operating voltages of 12V are compatible with the electrical part.
ADG426BRS-REEL7 Features
16 Channels
ADG426BRS-REEL7 Applications
There are a lot of Analog Devices Inc. ADG426BRS-REEL7 Analog Switches & Multiplexers ICs applications.
- Transmit
- RGB switches
- Central office
- DSLAMs
- Relay replacements
- Precision instrumentation
- Power routing
- Cell phones
- T1/E1 Terminals
- Video signal routing
