ADG426BRSZ-REEL
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 months ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 28-SSOP (0.209, 5.30mm Width) |
| Surface Mount | YES |
| Number of Pins | 28 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 28 |
| ECCN Code | EAR99 |
| Resistance | 80Ohm |
| Max Power Dissipation | 3.1mW |
| Technology | BICMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG426 |
| Pin Count | 28 |
| Operating Supply Voltage | 12V |
| Number of Channels | 16 |
| Interface | Parallel |
| Number of Circuits | 1 |
| Max Supply Voltage | 25V |
| Operating Supply Current | 100μA |
| Power Dissipation | 3.1mW |
| Logic Function | Multiplexer |
| Number of Inputs | 16 |
| Supply Type | Dual, Single |
| Supply Current-Max (Isup) | 0.5mA |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 110 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 80Ohm |
| High Level Output Current | 20mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 16:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 50pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Time (Ton, Toff) (Max) | 160ns, 150ns |
| Charge Injection | 8pC |
| Channel-to-Channel Matching (ΔRon) | 4 Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.02A |
| Voltage - Supply, Dual (V±) | ±15V |
| Height Seated (Max) | 2mm |
| Width | 5.3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG426BRSZ-REEL Overview
Packed in 28-SSOP (0.209, 5.30mm Width), the electronic component is convenient for shipping overseas. The advanced packaging method Tape & Reel (TR) provides high reliability. In Surface Mount, this analog switch is mounted. The ratio between the number of multiplexer and demultiplexer circuits is 16:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. Total terminations are 28. A electrical component with 16 channels is capable of high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. The electrical component body receives 28 pins. The multiplexer consists of 1 circuits. Try searching for the analog switch ic with ADG426 if you are looking for variants. This digital multiplexer has 80Ohm internal resistance. The functions of 28 pins can be found in the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 25V. The analog switch ic is of the Dual, Single supply type and is cost-effective. 100μA current would be enough for this multiplexer to operate. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 22V. 12V operating voltages can be used with this electrical part. Among the inputs that can be operated are the 16 inputs.
ADG426BRSZ-REEL Features
16 Channels
100μA Supply Current
ADG426BRSZ-REEL Applications
There are a lot of Analog Devices Inc. ADG426BRSZ-REEL Analog Switches & Multiplexers ICs applications.
- High speed data transmission line cards
- Frame Relay Equipment
- FTTH
- PDH Multiplexers
- CSU
- Battery Powered Instruments
- 65 V DACs
- Industrial control systems
- High reliability control systems
- HDTV
