ADG428BNZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 months ago) |
| Contact Plating | Tin |
| Mounting Type | Through Hole |
| Package / Case | 18-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 18 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 18 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | ADG428 |
| Pin Count | 18 |
| Operating Supply Voltage | 15V |
| Number of Channels | 8 |
| Interface | Parallel |
| Number of Circuits | 1 |
| Max Supply Voltage | 25V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Nominal Supply Current | 20μA |
| Power Dissipation | 1.6mW |
| Throw Configuration | DPST |
| Turn On Delay Time | 225 ns |
| Number of Inputs | 8 |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 100Ohm |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 11pF 40pF |
| On-state Resistance Match-Nom | 10Ohm |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 4pC |
| Channel-to-Channel Matching (ΔRon) | 10 Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 100Ohm |
| Signal Current-Max | 0.03A |
| Height | 3.3mm |
| Length | 22.86mm |
| Width | 6.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG428BNZ Overview
The electrical component comes in 18-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. This packaging method provides high reliability because it uses advanced packaging techniques. This analog switch is mounted in Through Hole. 8:1 is the number of circuits in the multiplexer and demultiplexer. An extended operating temperature of -40°C~85°C TA degrees Celsius. In total, 18 terminations have occurred. This electronic part offers high-quality output due to its 8 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. The electronic part body is injected with 18 pins. The circuits in this analogue multiplexer number 1. Try searching for the analog switch ic with ADG428 if you are looking for variants. The internal resistance of this digital multiplexer is 100Ohm. The datasheets for the 18 pins explain the functions. There is a standard Multiplexer or Switches analogue multiplexer here. It is normally recommended that users do not supply the multiplexer with voltages higher than 25V. Despite this switch device's dual supply capability, its voltage should not exceed 22V. There is an analog IC SINGLE-ENDED MULTIPLEXER integrated with this board. There is a voltage range of 15V operating voltages for the electrical part. The 8 inputs need to be operated in order to work. It has a Drain to Source resistance of 100Ohm ohms.
ADG428BNZ Features
8 Channels
Drain-to-Source resistance: 100Ohm
ADG428BNZ Applications
There are a lot of Analog Devices Inc. ADG428BNZ Analog Switches & Multiplexers ICs applications.
- PBX interfaces
- Mechanical reed relay replacement
- Voice over IP/DSL – Integrated Access Devices, Smart
- Fiber In The Loop (FITL)
- Avionics test equipment
- ISDN NT1/TA
- Automatic test equipment
- Public switching systems
- Transmit
- Digital access cross connects
