Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 1 month ago) |
Mounting Type |
Through Hole |
Package / Case |
16-DIP (0.300, 7.62mm) |
Surface Mount |
NO |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
24Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
7.7μW |
Technology |
CMOS |
Peak Reflow Temperature (Cel) |
NOT APPLICABLE |
Number of Functions |
4 |
Supply Voltage |
15V |
Time@Peak Reflow Temperature-Max (s) |
NOT APPLICABLE |
Base Part Number |
ADG431 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Operating Supply Voltage |
12V |
Number of Channels |
4 |
Interface |
Parallel |
Max Supply Voltage |
25V |
Min Supply Voltage |
5V |
Power Dissipation |
3.5μW |
Max Supply Current |
100nA |
Throw Configuration |
SPST |
Turn On Delay Time |
165 ns |
Voltage - Supply, Single/Dual (±) |
12V ±15V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
130 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
24Ohm |
Min Dual Supply Voltage |
13.5V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
68 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
9pF 9pF |
On-state Resistance Match-Nom |
0.85Ohm |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
90ns, 60ns |
Charge Injection |
5pC |
Channel-to-Channel Matching (ΔRon) |
1.2 Ω |
Crosstalk |
-85dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Drain to Source Resistance |
17mOhm |
Normal Position |
NC |
Height |
3.3mm |
Length |
20.07mm |
Width |
6.35mm |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG431BNZ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-DIP (0.300, 7.62mm). A high level of reliability can be achieved through the use of an advanced packaging method Tube. In Through Hole, this analog switch is mounted. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operational temperature extended around -40°C~85°C TA. A total of 16 terminations have been recorded. A high-quality output is provided by the electrical component's 4 channels. An 15V voltage supply should allow the electrical part to be turned on and run. The electrical component body receives 16 pins. A SPST - NC switching circuit is used for these analog switches. Try searching with ADG431 to find analog multiplexer variants. The internal resistance of this digital multiplexer is 24Ohm. Datasheets for functions of 16 pins are available. The analogue multiplexer in this example is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 25V. The digital multiplexer has a low cost Dual, Single supply. 5V should be the lowest voltage fed to the electronic component. The switch multiplexer may be damaged if it is exposed to voltage greater than 100nA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. If you are using dual power supplies, you should attach at least 13.5V. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. The electrical part can be operated at 12V voltage levels. Drain to Source resistance for this electronic component is 17mOhm.
ADG431BNZ Features
4 Channels
Switch Circuit: SPST - NC
Drain-to-Source resistance: 17mOhm
ADG431BNZ Applications
There are a lot of Analog Devices Inc. ADG431BNZ Analog Switches & Multiplexers ICs applications.
- HDTV
- PBXs
- Industrial control systems
- Microprocessor Controlled Analog Systems
- Cellular phones
- Wireless Local Loop
- Communications systems
- New designs requiring multiplexer functions
- Audio/video switches
- Digital Cross-Connects