Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 2 weeks ago) |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Surface Mount |
YES |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
24Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
7.7μW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG432 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Operating Supply Voltage |
12V |
Number of Channels |
4 |
Interface |
Parallel |
Max Supply Voltage |
25V |
Min Supply Voltage |
5V |
Operating Supply Current |
100pA |
Power Dissipation |
3.5μW |
Max Supply Current |
100nA |
Throw Configuration |
SPST |
Turn On Delay Time |
165 ns |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
130 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
24Ohm |
Min Dual Supply Voltage |
13.5V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
68 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
9pF 9pF |
On-state Resistance Match-Nom |
0.85Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
90ns, 60ns |
Charge Injection |
5pC |
Channel-to-Channel Matching (ΔRon) |
1.2 Ω |
Crosstalk |
-85dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Normal Position |
NO |
Voltage - Supply, Dual (V±) |
±15V |
Height Seated (Max) |
1.75mm |
Length |
9.9mm |
Width |
3.9mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG432BRZ-REEL Overview
Due to its 16-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Temperatures around -40°C~85°C TA are extended for operation. The total number of terminations is 16. The electronic part provides high-quality output because it has 4 channels. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. Into the electrical component body are injected 16 pins. A SPST - NO switching circuit is used to build these analog multiplexers. ADG432 can be used to search for analog multiplexer variants. There is 24Ohm internal resistance in this digital multiplexer. Please refer to the datasheets for 16 pins functions. It is a typical Multiplexer or Switches analog multiplexer. Users should never supply a voltage higher than 25V to a switch device. An effective Dual, Single supply digital multiplexer. The lowest voltage fed to the electronic component should be 5V. The analogue multiplexer could operate on 100pA current. The switch multiplexer may be damaged if it is exposed to voltage greater than 100nA. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. You should attach at least 13.5V voltage if you are using dual power supply. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. There is a voltage range of 12V operating voltages for the electrical part.
ADG432BRZ-REEL Features
4 Channels
Switch Circuit: SPST - NO
100pA Supply Current
ADG432BRZ-REEL Applications
There are a lot of Analog Devices Inc. ADG432BRZ-REEL Analog Switches & Multiplexers ICs applications.
- SONET/SDH ADM
- SONET
- MP3 players
- Isolation
- CSU
- Fault Tolerant Systems
- ISDN NT1/TA
- Industrial
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- PCMCIA cards