Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 2 weeks ago) |
Contact Plating |
Tin |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Surface Mount |
YES |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
24Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
7.7μW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG433 |
Pin Count |
16 |
Operating Supply Voltage |
12V |
Polarity |
Non-Inverting |
Number of Channels |
4 |
Interface |
Parallel |
Max Supply Voltage |
25V |
Min Supply Voltage |
5V |
Operating Supply Current |
100pA |
Power Dissipation |
3.5μW |
Max Supply Current |
100nA |
Throw Configuration |
SPST |
Turn On Delay Time |
165 ns |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
130 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
24Ohm |
Min Dual Supply Voltage |
13.5V |
High Level Output Current |
30mA |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
68 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
9pF 9pF |
On-state Resistance Match-Nom |
0.85Ohm |
Switch Circuit |
SPST - NO/NC |
Switch Time (Ton, Toff) (Max) |
90ns, 60ns |
Charge Injection |
5pC |
Channel-to-Channel Matching (ΔRon) |
1.2 Ω |
Crosstalk |
-85dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Dual (V±) |
±15V |
Height Seated (Max) |
1.75mm |
Length |
9.9mm |
Width |
3.9mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG433BRZ-REEL Overview
The electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.154, 3.90mm Width). Advanced packaging method Tape & Reel (TR) is used to provide high reliability. A switch device like this is mounted in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operation at a temperature around -40°C~85°C TA. Total terminations are 16. The electronic part provides high-quality output because it has 4 channels. Turning on and running the electrical part should be easy with a 15V voltage supply. An injection of 16 pins is performed into the body of the electrical component. A SPST - NO/NC switching circuit is used to build these analog multiplexers. Try searching for ADG433 variants of the analog switch ic. An switch multiplexer with 24Ohm internal resistance has a value of 24Ohm. You can find the functions of the 16 pins in the datasheets. Multiplexer or Switches is a typical switch device. A voltage higher than 25V should not normally be supplied to the switches. Analogue multiplexers of the Dual, Single supply type that are cost-effective. 5V is the lowest voltage that should be fed to the electronic electronic part. The analogue multiplexer could operate on 100pA current. The analogue multiplexer may be damaged if voltage is greater than 100nA. There is no problem with using dual supply voltage, but it should not exceed 22V. With dual power supplies, you should attach at least 13.5V. 12V operating voltages are supported by the electronic component.
ADG433BRZ-REEL Features
4 Channels
Switch Circuit: SPST - NO/NC
100pA Supply Current
ADG433BRZ-REEL Applications
There are a lot of Analog Devices Inc. ADG433BRZ-REEL Analog Switches & Multiplexers ICs applications.
- Avionics and Military Systems
- PCMCIA cards
- Microprocessor Controlled Analog Systems
- Channel Banks
- Cell phones
- CSU
- Wireless Local Loop
- PDH Multiplexers
- Mechanical reed relay replacement
- Residential Gateways, Home Gateway/Router