ADG436BNZ

70ns, 60ns (Typ) SPDT 12Ohm Typ Analog Switches BREAK-BEFORE-MAKE ADG436 16 Pins 250pA 15V 16-DIP (0.300, 7.62mm)

Manufacturer: Analog Devices Inc.
Nocochips NO: 84-ADG436BNZ
Package: 16-DIP (0.300, 7.62mm)
Datasheet: PDF
Stock: 417
Description: 70ns, 60ns (Typ) SPDT 12Ohm Typ Analog Switches BREAK-BEFORE-MAKE ADG436 16 Pins 250pA 15V 16-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Resistance	25Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	5.3mW
Technology	CMOS
Number of Functions	2
Supply Voltage	15V
Base Part Number	ADG436
Pin Count	16
Number of Outputs	4
Operating Supply Voltage	12V
Polarity	Non-Inverting
Number of Channels	2
Interface	Parallel
Max Supply Voltage	30V
Min Supply Voltage	3V
Test Frequency	1MHz
Operating Supply Current	50μA
Power Dissipation	5.3mW
Max Supply Current	350μA
Turn On Delay Time	125 ns
Voltage - Supply, Single/Dual (±)	3V~30V ±3V~20V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	120 ns
Max Dual Supply Voltage	20V
On-State Resistance (Max)	12Ohm Typ
Min Dual Supply Voltage	3V
High Level Output Current	20mA
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	72 dB
Current - Leakage (IS(off)) (Max)	250pA
Channel Capacitance (CS(off), CD(off))	13pF
On-state Resistance Match-Nom	1Ohm
Switch Circuit	SPDT
Switch Time (Ton, Toff) (Max)	70ns, 60ns (Typ)
Charge Injection	10pC
Channel-to-Channel Matching (ΔRon)	1 Ω
Crosstalk	-90dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Drain to Source Resistance	12Ohm
Height	5.33mm
Length	20.32mm
Width	7.11mm
Radiation Hardening	No
REACH SVHC	No SVHC
RoHS Status	ROHS3 Compliant
Lead Free	Contains Lead
Factory Lead Time	1 Week
Lifecycle Status	PRODUCTION (Last Updated: 2 weeks ago)
Mount	Through Hole
Mounting Type	Through Hole
Package / Case	16-DIP (0.300, 7.62mm)
Number of Pins	16
Operating Temperature	-40°C~85°C TA
Packaging	Tube
JESD-609 Code	e3
Pbfree Code	no
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
ECCN Code	EAR99

ADG436BNZ Overview

Shipping overseas is convenient with the electronic component packed in 16-DIP (0.300, 7.62mm). This packaging method provides high reliability because it uses advanced packaging techniques. A switch device like this is mounted in Through Hole. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. Extended operating temperature around -40°C~85°C TA. In total, 16 terminations have occurred. High-quality output is provided by the electronic component's 2 channels. It is safe to turn on and run the electronic component with a 15V voltage supply. An injection of 16 pins is performed into the body of the electrical component. A SPDT switching circuit is used to build these analog multiplexers. Use ADG436 to search for variants of the digital switches. This digital multiplexer has 25Ohm internal resistance. To find out what the functions of 16 pins are, please refer to their datasheets. It is a typical Multiplexer or Switches analog multiplexer. normally, users should not supply switches with voltages higher than 30V. The digital multiplexer has a low cost Dual, Single supply. A low voltage of 3V should be applied to the electronic component. For this multiplexer to operate, 50μA current would be sufficient. If put voltage greater than 350μA on the device, damage may be caused to the analogue multiplexer. Despite this switch's dual supply capability, its voltage should not exceed 20V. A dual power supply should have at least 3V voltage attached. 12V operating voltages can be used with this electrical part. Resistivity from Drain to Source is 12Ohm for this electronic part. An output of 4 is provided by the digital multiplexer.