Parameters |
ECCN Code |
EAR99 |
Resistance |
12Ohm |
Terminal Finish |
Tin/Lead (Sn85Pb15) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
5.3mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
2 |
Supply Voltage |
15V |
Reach Compliance Code |
not_compliant |
Time@Peak Reflow Temperature-Max (s) |
20 |
Base Part Number |
ADG436 |
Pin Count |
16 |
Number of Outputs |
4 |
Qualification Status |
Not Qualified |
Operating Supply Voltage |
12V |
Polarity |
Non-Inverting |
Number of Channels |
2 |
Interface |
Parallel |
Max Supply Voltage |
30V |
Min Supply Voltage |
3V |
Test Frequency |
1MHz |
Operating Supply Current |
50μA |
Power Dissipation |
5.3mW |
Max Supply Current |
350μA |
Turn On Delay Time |
125 ns |
Voltage - Supply, Single/Dual (±) |
3V~30V ±3V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
120 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
12Ohm Typ |
Min Dual Supply Voltage |
3V |
High Level Output Current |
20mA |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
72 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
13pF |
On-state Resistance Match-Nom |
1Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
70ns, 60ns (Typ) |
Charge Injection |
10pC |
Channel-to-Channel Matching (ΔRon) |
1 Ω |
Crosstalk |
-90dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Drain to Source Resistance |
12Ohm |
Height |
1.5mm |
Length |
10mm |
Width |
4mm |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
Contact Plating |
Lead, Tin |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Surface Mount |
YES |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ADG436BR Overview
The electrical component comes in 16-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. Advanced packaging method Tube is used to provide high reliability. In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have a ratio of 2:1. The operating temperature is extended to around -40°C~85°C TA. A total of 16 terminations have been recorded. Due to its 2 channels, the electrical component produces high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. As part of its design, the 16 series is equipped with this electronic component. These analog multiplexers are built based on SPDT switching circuits. Use ADG436 to search for variants of the digital switches. Internally, this switch multiplexer has a resistance of 12Ohm. For functions related to 16 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. A voltage higher than 30V should not normally be supplied to the switches. Analogue multiplexer with a Dual, Single supply type that is cost-effective. The lowest voltage the electronic part should receive is 3V. An operating current of 50μA would be sufficient for this switch device. The analogue multiplexer may be damaged if voltage is greater than 350μA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 20V. If you are using dual power supplies, you should attach at least 3V. The electronic component can function from 12V. There is 12Ohm resistance between the Drain and Source on this part. The analog switch ics has 4 outputs.
ADG436BR Features
2 Channels
Switch Circuit: SPDT
50μA Supply Current
Drain-to-Source resistance: 12Ohm
ADG436BR Applications
There are a lot of Analog Devices Inc. ADG436BR Analog Switches & Multiplexers ICs applications.
- Channelized and Unchannelized DS3 applications
- Public switching systems
- Sample hold systems
- Isolation
- Audio and video routing
- PBX interfaces
- Automotive applications
- Data Acquisition Systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- E1 Network Equipment