ADG441ABRZ-REEL
| Parameters | |
|---|---|
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 70Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.2mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG441 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 12V |
| Number of Channels | 4 |
| Interface | Parallel |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 10.8V |
| Power Dissipation | 1.2mW |
| Max Supply Current | 80μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 110 ns |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 60 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 70Ohm |
| Min Dual Supply Voltage | 13.5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 4pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 110ns, 60ns |
| Charge Injection | 1pC |
| Crosstalk | -100dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
ADG441ABRZ-REEL Overview
This electronic part is conveniently packaged in 16-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. This packaging method provides high reliability because it uses advanced packaging techniques. There is an analog multiplexer mounted in position Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. An extended operating temperature of -40°C~85°C TA degrees Celsius. In total, there have been 16 terminations. A electrical component with 4 channels is capable of high-quality output. When a voltage supply of 15V is used, the electronic component should be turned on and run. A key feature of the 16 series is the inclusion of this electronic part as part of its design. SPST - NC switching circuits are used in these analog switch ics. Try searching for ADG441 variants of the analog switch ic. The internal resistance of this digital multiplexer is 70Ohm. The functions of 16 pins can be found in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 25V. A analog switch ic that has a cost-effective Dual, Single supply type. 10.8V is the lowest voltage that should be fed to the electronic electronic part. It may damage the digital multiplexer if the voltage is higher than 80μA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. It is recommended that you attach at least 13.5V to your dual power supply. The electronic component can function from 12V.
ADG441ABRZ-REEL Features
4 Channels
Switch Circuit: SPST - NC
ADG441ABRZ-REEL Applications
There are a lot of Analog Devices Inc. ADG441ABRZ-REEL Analog Switches & Multiplexers ICs applications.
- Avionics test equipment
- PCMCIA cards
- SDH
- Modems
- T1/E1 Terminals
- Power routing
- Cable PC
- CSU
- Access Concentrators
- Digital access cross connects
