ADG442BNZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 70Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.2mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | NOT APPLICABLE |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | NOT APPLICABLE |
| Base Part Number | ADG442 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 12V |
| Number of Channels | 4 |
| Interface | Parallel |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 10.8V |
| Power Dissipation | 1.2mW |
| Max Supply Current | 80μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 110 ns |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 60 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 70Ohm |
| Min Dual Supply Voltage | 13.5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 4pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 110ns, 60ns |
| Charge Injection | 1pC |
| Crosstalk | -100dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 110Ohm |
| Normal Position | NO |
| Height | 3.3mm |
| Length | 20.07mm |
| Width | 6.35mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG442BNZ Overview
This electronic part is conveniently packaged in 16-DIP (0.300, 7.62mm), making it easy to ship abroad. High reliability is achieved by using advanced packaging method Tube. The multiplexer is located in Through Hole. Multiplexer and demultiplexer circuits have a number 1:1. Operating temperature extended to -40°C~85°C TA. A total of 16 terminations have been recorded. A 4 channel electronic part produces high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. The electronic part body is injected with 16 pins. On the other hand, analog switches can be constructed using SPST - NO switching circuits. Using the ADG442 search parameter, you can discover variants of the switch. It has an internal resistance of 70Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. In this analog multiplexer, the value is Multiplexer or Switches. A voltage higher than 25V should not normally be supplied to the switches. Digital switch that provides Dual, Single power at a cost-effective price. 10.8V is the lowest voltage that should be fed to the electronic electronic part. It may damage the digital multiplexer if the voltage is higher than 80μA. If put voltage greater than 22V on the multiplexer, damage may be caused to the device. You should attach at least 13.5V voltage if you are using dual power supply. A voltage of 12V can be used to operate the electronic component. There is 110Ohm resistance between Drain and Source for this electronic part.
ADG442BNZ Features
4 Channels
Switch Circuit: SPST - NO
Drain-to-Source resistance: 110Ohm
ADG442BNZ Applications
There are a lot of Analog Devices Inc. ADG442BNZ Analog Switches & Multiplexers ICs applications.
- DSUs
- Frame Relay Equipment
- Communication systems
- Audio and video signal routing
- ISDN NT1/TA
- Optical Applications
- Audio and video routing
- Avionics test equipment
- HDTV
- Mechanical reed relay replacement
