ADG442BRZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Resistance | 70Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG442 |
| Pin Count | 16 |
| Operating Supply Voltage | 12V |
| Polarity | Non-Inverting |
| Number of Channels | 4 |
| Interface | Parallel |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 10.8V |
| Nominal Supply Current | 80μA |
| Power Dissipation | 1.2mW |
| Max Supply Current | 80μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 110 ns |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 60 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 70Ohm |
| Min Dual Supply Voltage | 13.5V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 4pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 110ns, 60ns |
| Charge Injection | 1pC |
| Crosstalk | -100dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Height | 1.5mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG442BRZ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.154, 3.90mm Width). To ensure high reliability, a new packaging method Tube is used. The multiplexer is located in Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. Around -40°C~85°C TA is the extended operating temperature. A total of 16 terminations have been recorded. A high-quality output is provided by the electrical component's 4 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. This electronic part can be found in the 16 series. Based on SPST - NO switching circuits, these analog multiplexers work. Try searching for the analog switch ic with ADG442 if you are looking for variants. In this multiplexer, the internal resistance is 70Ohm. To find out what the 16 pins do, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. It is normally recommended that users do not supply the multiplexer with voltages higher than 25V. Analog switch ics with Dual, Single supply type are cost-effective. A low voltage of 10.8V should be applied to the electronic component. The analogue multiplexer may be damaged if voltage is greater than 80μA. If put voltage greater than 22V on the multiplexer, damage may be caused to the device. When using dual power supplies, you should attach at least 13.5V. There is a voltage range of 12V operating voltages for the electrical part.
ADG442BRZ Features
4 Channels
Switch Circuit: SPST - NO
ADG442BRZ Applications
There are a lot of Analog Devices Inc. ADG442BRZ Analog Switches & Multiplexers ICs applications.
- SDH/SONET multiplexers
- Data switching
- Video signal routing
- Precision data acquisition
- RGB switches
- New designs requiring multiplexer functions
- DVD-R
- Imaging
- Digital access cross connects
- Private Branch Exchange (PBX)
