ADG444ABR
| Parameters | |
|---|---|
| Max Supply Voltage | 25V |
| Power Dissipation | 1.2mW |
| Throw Configuration | SPST |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 70Ohm |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 4pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 110ns, 60ns |
| Charge Injection | 1pC |
| Crosstalk | -100dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 110ns |
| Switch-off Time-Max | 60ns |
| Normal Position | NC |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 70Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG444 |
| Pin Count | 16 |
| Operating Supply Voltage | 12V |
| Number of Channels | 4 |
ADG444ABR Overview
Shipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). To ensure high reliability, a new packaging method Tube is used. There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. Extended operating temperature around -40°C~85°C TA. In total, 16 terminations have occurred. By its 4 channels, the electronic component provides high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. A total of 16 pins are injected into the body of the electronic part. These analog multiplexers are built based on SPST - NC switching circuits. Try searching for the analog switch ic with ADG444 if you are looking for variants. Internally, this switch multiplexer has a resistance of 70Ohm. For functions related to 16 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 25V to the switch device in normal circumstances. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. The electrical part can be operated at 12V voltage levels.
ADG444ABR Features
4 Channels
Switch Circuit: SPST - NC
ADG444ABR Applications
There are a lot of Analog Devices Inc. ADG444ABR Analog Switches & Multiplexers ICs applications.
- Central office
- Ultrasound
- T1/E1 Terminals
- PBX interfaces
- Microprocessor Controlled Analog Systems
- Battery-powered systems
- Fiber In The Loop (FITL)
- E1 Multiplexer
- Industrial
- Existing multiplexer applications (both fault-protected and nonfault-protected)
