ADG444BNZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 70Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.2mW |
| Technology | CMOS |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Base Part Number | ADG444 |
| Pin Count | 16 |
| Operating Supply Voltage | 12V |
| Number of Channels | 4 |
| Interface | Parallel |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 10.8V |
| Power Dissipation | 1.2mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 110 ns |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 60 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 70Ohm |
| Min Dual Supply Voltage | 13.5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 4pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 110ns, 60ns |
| Charge Injection | 1pC |
| Crosstalk | -100dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height | 3.3mm |
| Length | 20.07mm |
| Width | 6.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG444BNZ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-DIP (0.300, 7.62mm). The advanced packaging method Tube provides high reliability. It is mounted in the position Through Hole. There is 1:1 ratio between the number of multiplexers and demultiplexers. Increasing operating temperature to around -40°C~85°C TA. A total of 16 terminations have been recorded. A 4 channel electronic part produces high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. The electrical component body receives 16 pins. Based on SPST - NC switching circuits, these analog multiplexers work. Try searching for ADG444 variants of the analog switch ic. An switch multiplexer with 70Ohm internal resistance has a value of 70Ohm. For details about the functions of 16 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 25V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. In order for the electronic part to function properly, the lowest voltage should be 10.8V. When the digital multiplexer is charged above 1μA, damage can occur. Despite this switch device's dual supply capability, its voltage should not exceed 22V. In the case of dual power supplies, you should connect at least 13.5V. A voltage of 12V can be used to operate the electronic component.
ADG444BNZ Features
4 Channels
Switch Circuit: SPST - NC
ADG444BNZ Applications
There are a lot of Analog Devices Inc. ADG444BNZ Analog Switches & Multiplexers ICs applications.
- Signal routing between systems
- Medical systems
- USB 1.1 signal switching circuits
- Relay replacements
- Isolation
- Transmit
- Precision data acquisition
- Data Acquisition Systems
- Cell phones
- Voice over IP/DSL – Integrated Access Devices, Smart
