Parameters |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
60 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
70Ohm |
Min Dual Supply Voltage |
13.5V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
60 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
4pF 4pF |
On-state Resistance Match-Nom |
1Ohm |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
110ns, 60ns |
Charge Injection |
1pC |
Crosstalk |
-100dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Drain to Source Resistance |
40mOhm |
Normal Position |
NC |
Height Seated (Max) |
1.75mm |
Length |
9.9mm |
Width |
3.9mm |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Surface Mount |
YES |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
70Ohm |
Terminal Finish |
Tin/Lead (Sn85Pb15) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
1.2mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Reach Compliance Code |
not_compliant |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG444 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Operating Supply Voltage |
12V |
Number of Channels |
4 |
Interface |
Parallel |
Max Supply Voltage |
25V |
Min Supply Voltage |
10.8V |
Power Dissipation |
1.2mW |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
110 ns |
Voltage - Supply, Single/Dual (±) |
12V ±15V |
Supply Type |
Dual, Single |
ADG444BR Overview
Presented in 16-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. High reliability is provided by advanced packaging method Tube. In Surface Mount, you'll find this switch device. 1:1 is the ratio of multiplexer to demultiplexer circuits. Increasing operating temperature to around -40°C~85°C TA. Total terminations are 16. As a result of its 4 channels, this electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. Electronic part bodies are injected with 16 pins. SPST - NC switching circuits are used in these analog switch ics. Using the ADG444 search parameter, you can discover variants of the switch. In this multiplexer, the internal resistance is 70Ohm. Please refer to the datasheets for 16 pins functions. Multiplexer or Switches is a typical switch device. normally, users should not supply switches with voltages higher than 25V. The analog switch ic is of the Dual, Single supply type and is cost-effective. The lowest voltage the electronic part should receive is 10.8V. The analogue multiplexer may be damaged if voltage is greater than 1μA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. The voltage should be at least 13.5V if you are using dual power supplies. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. A voltage of 12V can be used to operate the electronic component. It has a Drain to Source resistance of 40mOhm ohms.
ADG444BR Features
4 Channels
Switch Circuit: SPST - NC
Drain-to-Source resistance: 40mOhm
ADG444BR Applications
There are a lot of Analog Devices Inc. ADG444BR Analog Switches & Multiplexers ICs applications.
- Remote Powered Equipment
- Sample-and-hold systems
- Multiplexers
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Fiber to the Home
- FTTH
- Cellular phones
- Mechanical reed relay replacement
- Signal routing between systems
- PBXs