ADG452BR-REEL7
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 5Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Additional Feature | ALSO OPERATE WITH 12V SINGLE SUPPLY |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG452 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 9V |
| Number of Channels | 4 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 5V |
| Power Dissipation | 600mW |
| Throw Configuration | SPST |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Max Dual Supply Voltage | 15V |
| On-State Resistance (Max) | 5Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 65 dB |
| Neg Supply Voltage-Max (Vsup) | -20V |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 37pF 37pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 180ns, 140ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 220ns |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±4.5V~20V |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| RoHS Status | Non-RoHS Compliant |
ADG452BR-REEL7 Overview
This electronic part is conveniently packaged in 16-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Operation at a temperature around -40°C~85°C TA. A total of 16 terminations have been recorded. This electronic part offers high-quality output due to its 4 channels. An 5V voltage supply should allow the electrical part to be turned on and run. The electronic part body is injected with 16 pins. Circuits based on SPST - NO switching are used to construct these analog switch ics. Try searching for the analog switch ic with ADG452 if you are looking for variants. As far as internal resistance is concerned, it has 5Ohm. For details about the functions of 16 pins, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. Multiplexers should not be powered above 12V in normal situations. 5V should be the lowest voltage fed to the electronic component. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 15V. When using dual power supplies, you should attach at least 5V. There are SEPARATE OUTPUT outputs on this analog switch ic. A voltage of 9V can be used to operate the electronic component. Check out the electrical component's additional features, such as the following: ALSO OPERATE WITH 12V SINGLE SUPPLY.
ADG452BR-REEL7 Features
4 Channels
Switch Circuit: SPST - NO
Additional Features: ALSO OPERATE WITH 12V SINGLE SUPPLY
ADG452BR-REEL7 Applications
There are a lot of Analog Devices Inc. ADG452BR-REEL7 Analog Switches & Multiplexers ICs applications.
- Channel Banks
- Communications systems
- Cross Connects
- HDTV
- Digital Cross-Connects
- Signal routing between systems
- Communication systems
- Ultrasound
- Microprocessor controlled systems
- Industrial
