ADG452BRZ-REEL7

180ns, 140ns SPST - NO 5Ohm Analog Switches BREAK-BEFORE-MAKE ADG452 16 Pins 500pA 5V 16-SOIC (0.154, 3.90mm Width)

Manufacturer: Analog Devices Inc.
Nocochips NO: 84-ADG452BRZ-REEL7
Package: 16-SOIC (0.154, 3.90mm Width)
Datasheet: PDF
Stock: 455
Description: 180ns, 140ns SPST - NO 5Ohm Analog Switches BREAK-BEFORE-MAKE ADG452 16 Pins 500pA 5V 16-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Switch-on Time-Max	220ns
Normal Position	NO
Voltage - Supply, Dual (V±)	±4.5V~20V
Height Seated (Max)	1.75mm
Length	9.9mm
Width	3.9mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant
Lead Free	Contains Lead
Factory Lead Time	1 Week
Lifecycle Status	PRODUCTION (Last Updated: 2 weeks ago)
Contact Plating	Tin
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-SOIC (0.154, 3.90mm Width)
Number of Pins	16
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
JESD-609 Code	e3
Pbfree Code	no
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
ECCN Code	EAR99
Resistance	5Ohm
Additional Feature	ALSO OPERATE WITH 12V SINGLE SUPPLY
Subcategory	Multiplexer or Switches
Max Power Dissipation	17.5μW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	5V
Terminal Pitch	1.27mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	ADG452
Pin Count	16
Operating Supply Voltage	9V
Polarity	Non-Inverting
Number of Channels	4
Interface	Parallel
Max Supply Voltage	12V
Min Supply Voltage	5V
Operating Supply Current	100pA
Power Dissipation	17.5μW
Max Supply Current	500nA
Throw Configuration	SPST
Turn On Delay Time	180 ns
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-5V
Turn-Off Delay Time	140 ns
Max Dual Supply Voltage	15V
On-State Resistance (Max)	5Ohm
Min Dual Supply Voltage	5V
High Level Output Current	100mA
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	65 dB
Neg Supply Voltage-Max (Vsup)	-20V
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	37pF 37pF
On-state Resistance Match-Nom	0.3Ohm
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	180ns, 140ns
Charge Injection	20pC
Channel-to-Channel Matching (ΔRon)	100m Ω
Crosstalk	-90dB @ 1MHz
Switching	BREAK-BEFORE-MAKE

ADG452BRZ-REEL7 Overview

This electronic part is conveniently packaged in 16-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. In Surface Mount, you'll find this switch device. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. Total terminations are 16. A electrical component with 4 channels is capable of high-quality output. An 5V voltage supply should allow the electrical part to be turned on and run. An electrical component of this type can be found in the 16 series. On the other hand, analog switches can be constructed using SPST - NO switching circuits. Try searching for ADG452 variants of the analog switch ic. As far as internal resistance is concerned, it has 5Ohm. For details about the functions of 16 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. Users shouldn't supply more than 12V voltage to the switch device. Dual, Single supply type digital switch with a low cost. A low voltage of 5V should be applied to the electronic component. The analogue multiplexer could operate on 100pA current. If you put voltage higher than 500nA on the digital multiplexer, damage may occur. For this multiplexer, dual supply voltage is feasible, but it should not exceed 15V. In the case of dual power supplies, you should connect at least 5V. There is a voltage range of 9V operating voltages for the electrical part. There is also ALSO OPERATE WITH 12V SINGLE SUPPLY to look out for in this electronic part.