ADG453BRUZ
| Parameters | |
|---|---|
| Pin Count | 16 |
| Operating Supply Voltage | 9V |
| Polarity | Non-Inverting |
| Number of Channels | 4 |
| Interface | Parallel |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 100pA |
| Power Dissipation | 17.5μW |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 180 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 140 ns |
| Max Dual Supply Voltage | 15V |
| On-State Resistance (Max) | 5Ohm |
| Min Dual Supply Voltage | 5V |
| High Level Output Current | 100mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 65 dB |
| Neg Supply Voltage-Max (Vsup) | -20V |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 37pF 37pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 180ns, 140ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 220ns |
| Drain to Source Resistance | 4Ohm |
| Voltage - Supply, Dual (V±) | ±4.5V~20V |
| Height | 1.05mm |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 5Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Additional Feature | ALSO OPERATE WITH 12V SINGLE SUPPLY |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 17.5μW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG453 |
ADG453BRUZ Overview
Packed in 16-TSSOP (0.173, 4.40mm Width), the electronic component is convenient for shipping overseas. This high-reliability packaging method uses advanced packaging methods Tube. Surface Mount is where this multiplexer is located. 1:1 is the ratio between multiplexers and demultiplexers. Operating temperature around -40°C~85°C TA extended. In total, 16 terminations have occurred. Due to its 4 channels, the electrical component produces high-quality output. Powered by a 5V voltage supply, the electrical part should be switched on and run. It is injected into the electrical part body with 16 pins. Multiplexers built on a SPST - NO/NC switching circuit are built. Use ADG453 to search for variants of the digital switches. As far as internal resistance is concerned, it has 5Ohm. For functions related to 16 pins, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. Digital switch that provides Dual, Single power at a cost-effective price. There should be 5V voltage fed to the electrical part below 5V. The switch device would be able to operate with 100pA current. A digital multiplexer may suffer damage if voltage is applied above 500nA. Despite this switch's dual supply capability, its voltage should not exceed 15V. The voltage should be at least 5V if you are using dual power supplies. 9V operating voltages can be used with this electrical part. This electrical component also includes additional features such as ALSO OPERATE WITH 12V SINGLE SUPPLY. There is 4Ohm Drain to Source resistance on this electronic part.
ADG453BRUZ Features
4 Channels
Switch Circuit: SPST - NO/NC
100pA Supply Current
Additional Features: ALSO OPERATE WITH 12V SINGLE SUPPLY
Drain-to-Source resistance: 4Ohm
ADG453BRUZ Applications
There are a lot of Analog Devices Inc. ADG453BRUZ Analog Switches & Multiplexers ICs applications.
- Multi-Line E1 Interface Cards
- Precision instrumentation
- Avionics and Military Systems
- Medical
- PBXs
- Sample-and-hold systems
- Audio/video switches
- Relay replacements
- ATM
- Ultrasound
