banner_page

ADG506AKN

300ns, 300ns 300Ohm DUAL Analog Switches BREAK-BEFORE-MAKE ADG506 28 Pins 1nA 15V 28-DIP (0.600, 15.24mm)


  • Manufacturer: Analog Devices Inc.
  • Nocochips NO: 84-ADG506AKN
  • Package: 28-DIP (0.600, 15.24mm)
  • Datasheet: PDF
  • Stock: 419
  • Description: 300ns, 300ns 300Ohm DUAL Analog Switches BREAK-BEFORE-MAKE ADG506 28 Pins 1nA 15V 28-DIP (0.600, 15.24mm)(Kg)

Details

Tags

Parameters
Mounting Type Through Hole
Package / Case 28-DIP (0.600, 15.24mm)
Surface Mount NO
Number of Pins 28
Operating Temperature -40°C~85°C TA
Packaging Tube
JESD-609 Code e0
Pbfree Code no
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 28
ECCN Code EAR99
Resistance 300Ohm
Subcategory Multiplexer or Switches
Max Power Dissipation 470mW
Technology CMOS
Terminal Position DUAL
Number of Functions 1
Supply Voltage 15V
Terminal Pitch 2.54mm
Base Part Number ADG506
Pin Count 28
Number of Channels 16
Interface Parallel
Number of Circuits 1
Max Supply Voltage 16.5V
Min Supply Voltage 10.8V
Analog IC - Other Type SINGLE-ENDED MULTIPLEXER
Operating Supply Current 600μA
Nominal Supply Current 1.5mA
Power Dissipation 10mW
Propagation Delay 300 ns
Turn On Delay Time 450 ns
Voltage - Supply, Single/Dual (±) 10.8V~16.5V ±10.8V~16.5V
Neg Supply Voltage-Nom (Vsup) -15V
Turn-Off Delay Time 450 ns
Max Dual Supply Voltage 16.5V
On-State Resistance (Max) 300Ohm
Min Dual Supply Voltage 10.8V
Multiplexer/Demultiplexer Circuit 16:1
Off-state Isolation-Nom 68 dB
Current - Leakage (IS(off)) (Max) 1nA
Channel Capacitance (CS(off), CD(off)) 5pF 44pF
On-state Resistance Match-Nom 22.5Ohm
Switch Time (Ton, Toff) (Max) 300ns, 300ns
Charge Injection 4pC
Channel-to-Channel Matching (ΔRon) 15 Ω
Switching BREAK-BEFORE-MAKE
Signal Current-Max 0.02A
Height Seated (Max) 5.08mm
Length 36.705mm
Radiation Hardening No
RoHS Status Non-RoHS Compliant
Lead Free Contains Lead

ADG506AKN Overview


The electronic part can be shipped overseas conveniently because it is packaged in 28-DIP (0.600, 15.24mm). This high-reliability packaging method uses advanced packaging methods Tube. The multiplexer is located in Through Hole. Multiplexers and demultiplexers have a number of circuits 16:1. Temperatures around -40°C~85°C TA are extended for operation. Total terminations are 28. High-quality output is provided by the electronic component's 16 channels. An 15V voltage supply should allow the electrical part to be turned on and run. An electrical component like this is included in the 28 series. The multiplexer consists of 1 circuits. Use ADG506 to search for variants of the digital switches. There is 300Ohm internal resistance in this digital multiplexer. For details about the functions of 28 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. Users shouldn't supply more than 16.5V voltage to the switch device. It is recommended to use 10.8V as the lowest voltage for the electrical part. In order to operate this switch device, it would need a current of 600μA. Despite this switch's dual supply capability, its voltage should not exceed 16.5V. You should attach at least 10.8V voltage if you are using dual power supply. A SINGLE-ENDED MULTIPLEXER analog IC is integrated into the board.

ADG506AKN Features


16 Channels
600μA Supply Current

ADG506AKN Applications


There are a lot of Analog Devices Inc. ADG506AKN Analog Switches & Multiplexers ICs applications.

  • SONET
  • Public switching systems
  • CSU
  • E1 Network Equipment
  • Communications systems
  • Modems
  • Precision data acquisition
  • PCMCIA cards
  • USB 1.1 signal switching circuits
  • Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads

Write a review

Note: HTML is not translated!
    Bad           Good