ADG506ATQ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Mounting Type | Through Hole |
| Package / Case | 28-CDIP (0.600, 15.24mm) |
| Surface Mount | NO |
| Number of Pins | 28 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| ECCN Code | EAR99 |
| Resistance | 300Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 28mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | NOT APPLICABLE |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT APPLICABLE |
| Base Part Number | ADG506 |
| Pin Count | 28 |
| Qualification Status | Not Qualified |
| Number of Channels | 16 |
| Interface | Parallel |
| Number of Circuits | 1 |
| Max Supply Voltage | 16.5V |
| Min Supply Voltage | 10.8V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Operating Supply Current | 600μA |
| Power Dissipation | 10mW |
| Propagation Delay | 300 ns |
| Turn On Delay Time | 400 ns |
| Voltage - Supply, Single/Dual (±) | 10.8V~16.5V ±10.8V~16.5V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 400 ns |
| Max Dual Supply Voltage | 16.5V |
| On-State Resistance (Max) | 300Ohm |
| Min Dual Supply Voltage | 10.8V |
| Multiplexer/Demultiplexer Circuit | 16:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 44pF |
| On-state Resistance Match-Nom | 22.5Ohm |
| Switch Time (Ton, Toff) (Max) | 300ns, 300ns |
| Charge Injection | 4pC |
| Channel-to-Channel Matching (ΔRon) | 15 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.02A |
| Height Seated (Max) | 5.59mm |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG506ATQ Overview
Due to its 28-CDIP (0.600, 15.24mm) packaging, the electronic part is convenient for international shipping. High reliability is achieved by using advanced packaging method Tube. In Through Hole, this analog switch is mounted. 16:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature around -55°C~125°C TA extended. In total, there are 28 terminations. High-quality output is provided by the electronic component's 16 channels. It is safe to turn on and run the electronic component with a 15V voltage supply. 28 pins are injected to the electronic part body. 1 circuits are used in this analogue multiplexer. Use ADG506 to search for variants of the digital switches. There is 300Ohm internal resistance in this digital multiplexer. To find out what the 28 pins do, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 16.5V. The lowest voltage the electronic part should receive is 10.8V. For this multiplexer to operate, 600μA current would be sufficient. If put voltage greater than 16.5V on the multiplexer, damage may be caused to the device. The voltage should be at least 10.8V if you are using dual power supplies. It is integrated with SINGLE-ENDED MULTIPLEXER analog ICs.
ADG506ATQ Features
16 Channels
600μA Supply Current
ADG506ATQ Applications
There are a lot of Analog Devices Inc. ADG506ATQ Analog Switches & Multiplexers ICs applications.
- Relay Replacement
- Intelligent PBX
- Cell phones
- DSUs
- SDH/SONET multiplexers
- CSU
- Battery Powered Systems
- PBXs
- Power routing
- Fiber to the Home
