Parameters |
Mounting Type |
Through Hole |
Package / Case |
28-DIP (0.600, 15.24mm) |
Surface Mount |
NO |
Number of Pins |
28 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
JESD-609 Code |
e0 |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
28 |
ECCN Code |
EAR99 |
Resistance |
300Ohm |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Terminal Position |
DUAL |
Peak Reflow Temperature (Cel) |
NOT APPLICABLE |
Number of Functions |
1 |
Supply Voltage |
15V |
Reach Compliance Code |
not_compliant |
Time@Peak Reflow Temperature-Max (s) |
NOT APPLICABLE |
Base Part Number |
ADG507 |
Pin Count |
28 |
Qualification Status |
Not Qualified |
Number of Channels |
1 |
Number of Circuits |
2 |
Max Supply Voltage |
16.5V |
Min Supply Voltage |
10.8V |
Analog IC - Other Type |
DIFFERENTIAL MULTIPLEXER |
Power Dissipation |
470mW |
Number of Inputs |
16 |
Voltage - Supply, Single/Dual (±) |
10.8V~16.5V ±10.8V~16.5V |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Max Dual Supply Voltage |
16.5V |
On-State Resistance (Max) |
300Ohm |
Min Dual Supply Voltage |
10.8V |
Multiplexer/Demultiplexer Circuit |
8:1 |
Off-state Isolation-Nom |
68 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
5pF 22pF |
On-state Resistance Match-Nom |
22.5Ohm |
Switch Time (Ton, Toff) (Max) |
300ns, 300ns |
Charge Injection |
4pC |
Channel-to-Channel Matching (ΔRon) |
15 Ω |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
300ns |
Switch-off Time-Max |
300ns |
Drain to Source Resistance |
600Ohm |
Height Seated (Max) |
5.08mm |
Length |
36.705mm |
RoHS Status |
Non-RoHS Compliant |
ADG507AKN Overview
Shipping overseas is convenient due to the electrical component's packing in 28-DIP (0.600, 15.24mm). A high level of reliability can be achieved through the use of an advanced packaging method Tube. This analog switch is mounted in Through Hole. Multiplexer and demultiplexer circuits have a number 8:1. Extended operating temperature around -40°C~85°C TA. Total terminations are 28. Due to its 1 channels, the electrical component produces high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. There are 28 pins injected into the electronic part body. A 2 circuit is present in this switch device. ADG507 can be used to search for analog multiplexer variants. As far as internal resistance is concerned, it has 300Ohm. Datasheets for functions of 28 pins are available. The analogue multiplexer in this example is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 16.5V. In order for the electronic part to function properly, the lowest voltage should be 10.8V. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 16.5V. In the case of dual power supplies, you should connect at least 10.8V. An analog IC with the number DIFFERENTIAL MULTIPLEXER is integrated into this board. There are 16 inputs to be operated. The Drain to Source resistance of this electronic component is 600Ohm.
ADG507AKN Features
1 Channels
Drain-to-Source resistance: 600Ohm
ADG507AKN Applications
There are a lot of Analog Devices Inc. ADG507AKN Analog Switches & Multiplexers ICs applications.
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Cable Modem
- Video switching
- Digital access cross connects
- SDH/SONET multiplexers
- PBX interfaces
- Optical Applications
- Audio/video switches
- CSU
- Battery-powered systems