ADG507AKRU
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 28-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 28 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 28 |
| ECCN Code | EAR99 |
| Resistance | 300Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG507 |
| Pin Count | 28 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Interface | Parallel |
| Number of Circuits | 2 |
| Max Supply Voltage | 16.5V |
| Min Supply Voltage | 10.8V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Nominal Supply Current | 1.5mA |
| Power Dissipation | 28mW |
| Propagation Delay | 300 ns |
| Turn On Delay Time | 450 ns |
| Number of Inputs | 16 |
| Voltage - Supply, Single/Dual (±) | 10.8V~16.5V ±10.8V~16.5V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 450 ns |
| Max Dual Supply Voltage | 16.5V |
| On-State Resistance (Max) | 300Ohm |
| Min Dual Supply Voltage | 10.8V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 22pF |
| On-state Resistance Match-Nom | 22.5Ohm |
| Switch Time (Ton, Toff) (Max) | 300ns, 300ns |
| Charge Injection | 4pC |
| Channel-to-Channel Matching (ΔRon) | 15 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Length | 9.7mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG507AKRU Overview
Shipping overseas is convenient with the electronic component packed in 28-TSSOP (0.173, 4.40mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. A switch device like this is mounted in Surface Mount. In the multiplexer and demultiplexer, 8:1 represents the number of circuits. An extended operating temperature of -40°C~85°C TA degrees Celsius. The total number of terminations is 28. As a result of its 1 channels, this electronic component provides high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. Into the electrical component body are injected 28 pins. The circuits in this analogue multiplexer number 2. Look for analog switch ic variants by searching with ADG507. The internal resistance of this digital multiplexer is 300Ohm. To find out what the 28 pins do, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. A voltage higher than 16.5V should not normally be supplied to the switches. Analogue multiplexers of the Dual, Single supply type that are cost-effective. There should be 10.8V voltage fed to the electrical part below 10.8V. If put voltage greater than 16.5V on the multiplexer, damage may be caused to the device. For dual power supplies, a voltage of at least 10.8V should be attached. Integrated with an analog IC DIFFERENTIAL MULTIPLEXER. This electrical part is compatible with 15V operating voltages. There are 16 inputs to be operated.
ADG507AKRU Features
1 Channels
ADG507AKRU Applications
There are a lot of Analog Devices Inc. ADG507AKRU Analog Switches & Multiplexers ICs applications.
- Industrial and process control systems
- Fault Tolerant Systems
- Audio and video routing
- Ultrasound
- Central office
- Sample hold systems
- RGB switches
- Power routing
- Multi-Line E1 Interface Cards
- Avionics
