Parameters |
Mounting Type |
Surface Mount |
Package / Case |
20-LCC (J-Lead) |
Surface Mount |
YES |
Number of Pins |
20 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
20 |
ECCN Code |
EAR99 |
Resistance |
300Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
470mW |
Technology |
CMOS |
Terminal Position |
QUAD |
Terminal Form |
J BEND |
Peak Reflow Temperature (Cel) |
220 |
Number of Functions |
1 |
Supply Voltage |
15V |
Reach Compliance Code |
not_compliant |
Time@Peak Reflow Temperature-Max (s) |
20 |
Base Part Number |
ADG508 |
Pin Count |
20 |
Qualification Status |
Not Qualified |
Number of Channels |
8 |
Interface |
Parallel |
Number of Circuits |
1 |
Max Supply Voltage |
16.5V |
Min Supply Voltage |
10.8V |
Analog IC - Other Type |
SINGLE-ENDED MULTIPLEXER |
Power Dissipation |
27mW |
Throw Configuration |
DPST |
Propagation Delay |
300 ns |
Turn On Delay Time |
450 ns |
Voltage - Supply, Single/Dual (±) |
10.8V~16.5V ±10.8V~16.5V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
450 ns |
Max Dual Supply Voltage |
16.5V |
On-State Resistance (Max) |
300Ohm |
Min Dual Supply Voltage |
10.8V |
Multiplexer/Demultiplexer Circuit |
8:1 |
Off-state Isolation-Nom |
68 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
5pF 22pF |
On-state Resistance Match-Nom |
22.5Ohm |
Switch Time (Ton, Toff) (Max) |
300ns, 300ns |
Charge Injection |
4pC |
Channel-to-Channel Matching (ΔRon) |
15 Ω |
Switching |
BREAK-BEFORE-MAKE |
Signal Current-Max |
0.02A |
Height Seated (Max) |
4.57mm |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
ADG508AKP Overview
The electrical component comes in 20-LCC (J-Lead) packaging, which makes it convenient to ship overseas. High reliability is achieved by using advanced packaging method Tube. In Surface Mount, you'll find this switch device. Multiplexer and demultiplexer circuits have a number 8:1. Operational temperature extended around -40°C~85°C TA. A total of 20 terminations have been recorded. By its 8 channels, the electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. As part of its design, the 20 series is equipped with this electronic component. The multiplexer consists of 1 circuits. Use ADG508 to search for variants of the digital switches. An switch multiplexer with 300Ohm internal resistance has a value of 300Ohm. The functions of 20 pins can be found in the datasheets. This switch device is a typical Multiplexer or Switches. A voltage higher than 16.5V should not normally be supplied to the switches. Dual, Single supply type digital switch with a low cost. 10.8V is the lowest voltage that should be fed to the electronic electronic part. If put voltage greater than 16.5V on the multiplexer, damage may be caused to the device. When using dual power supplies, you should attach at least 10.8V. A SINGLE-ENDED MULTIPLEXER analog IC is integrated into the board.
ADG508AKP Features
8 Channels
ADG508AKP Applications
There are a lot of Analog Devices Inc. ADG508AKP Analog Switches & Multiplexers ICs applications.
- Fiber to the Home
- Cable PC
- Channelized and Unchannelized DS3 applications
- Central office
- SONET
- Relay Replacement
- Multi-Line E1 Interface Cards
- Precision data acquisition
- Avionics
- Industrial control systems