ADG508AKR-REEL
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 300Ohm |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG508 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Channels | 8 |
| Interface | Parallel |
| Number of Circuits | 1 |
| Max Supply Voltage | 16.5V |
| Min Supply Voltage | 10.8V |
| Operating Supply Current | 600μA |
| Power Dissipation | 27mW |
| Throw Configuration | DPST |
| Propagation Delay | 300 ns |
| Turn On Delay Time | 450 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 10.8V~16.5V ±10.8V~16.5V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 450 ns |
| Max Dual Supply Voltage | 16.5V |
| On-State Resistance (Max) | 300Ohm |
| Min Dual Supply Voltage | 10.8V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 22pF |
| On-state Resistance Match-Nom | 22.5Ohm |
| Switch Time (Ton, Toff) (Max) | 300ns, 300ns |
| Charge Injection | 4pC |
| Channel-to-Channel Matching (ΔRon) | 15 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.02A |
| Length | 9.9mm |
| Width | 3.9mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG508AKR-REEL Overview
Presented in 16-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have the same number of circuits 8:1. Temperatures around -40°C~85°C TA are extended for operation. Total terminations are 16. The electronic part delivers high-quality output through its 8 channels. It is safe to turn on and run the electronic component with a 15V voltage supply. An injection of 16 pins is performed into the body of the electrical component. The circuits in this analogue multiplexer number 1. Try searching with ADG508 to find analog multiplexer variants. There is 300Ohm internal resistance in this digital multiplexer. Please refer to the datasheets for 16 pins functions. It is generally not recommended to supply a voltage higher than 16.5V to the switch device in normal circumstances. The digital multiplexer has a low cost Dual, Single supply. The lowest voltage fed to the electronic component should be 10.8V. For this multiplexer to operate, 600μA current would be sufficient. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 16.5V. If you are using dual power supplies, you should attach at least 10.8V. 15V operating voltages are supported by the electronic component.
ADG508AKR-REEL Features
8 Channels
600μA Supply Current
ADG508AKR-REEL Applications
There are a lot of Analog Devices Inc. ADG508AKR-REEL Analog Switches & Multiplexers ICs applications.
- Audio and video switching
- New designs requiring multiplexer functions
- Cross Connects
- Digital access cross connects
- Microprocessor Controlled Analog Systems
- Fiber In The Loop (FITL)
- Communication systems
- Frame Relay Equipment
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Audio/video switches
