ADG508FBNZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Termination | Through Hole |
| ECCN Code | EAR99 |
| Resistance | 300Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 3.3mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | ADG508 |
| Pin Count | 16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 8 |
| Interface | Parallel |
| Number of Circuits | 1 |
| Max Supply Voltage | 16.5V |
| Min Supply Voltage | 10.8V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Nominal Supply Current | 600μA |
| Power Dissipation | 3mW |
| Max Supply Current | 1μA |
| Throw Configuration | DPST |
| Propagation Delay | 300 ns |
| Turn On Delay Time | 230 ns |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 130 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 270Ohm Typ |
| High Level Output Current | 20mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 93 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 22pF |
| On-state Resistance Match-Nom | 8.1Ohm |
| Switch Time (Ton, Toff) (Max) | 230ns, 130ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 8.1 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 300Ohm |
| Signal Current-Max | 0.02A |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 3.3mm |
| Length | 20.07mm |
| Width | 6.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG508FBNZ Overview
Due to its 16-DIP (0.300, 7.62mm) packaging, the electronic part is convenient for international shipping. High reliability is provided by advanced packaging method Tube. Multiplexers like this are mounted in the Through Hole position. 8:1 is the ratio between multiplexers and demultiplexers. An extended operating temperature of -40°C~85°C TA degrees Celsius. Total terminations are 16. By its 8 channels, the electronic component provides high-quality output. With a 15V voltage supply, the electrical component should be turned on and run. This electronic part can be found in the 16 series. It consists of 1 circuits. Try searching with ADG508 if you're looking for variants. A 300Ohm internal resistance characterizes this multiplexer. For functions related to 16 pins, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. Users shouldn't supply more than 16.5V voltage to the switch device. 10.8V should be the lowest voltage fed to the electronic component. Putting voltage greater than 1μA on the multiplexer may cause damage. Despite this switch device's dual supply capability, its voltage should not exceed 22V. It is integrated with a SINGLE-ENDED MULTIPLEXER analog IC. 15V operating voltages are supported by the electronic component. It has a Drain to Source resistance of 300Ohm ohms.
ADG508FBNZ Features
8 Channels
Drain-to-Source resistance: 300Ohm
ADG508FBNZ Applications
There are a lot of Analog Devices Inc. ADG508FBNZ Analog Switches & Multiplexers ICs applications.
- Precision test equipment
- Wireless Local Loop
- Power routing
- Remote Powered Equipment
- Audio signal routing
- Battery-powered systems
- SONET/SDH ADM
- Data switching
- Relay replacements
- Transmit
