ADG508FBRNZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 300Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 3.3mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG508 |
| Pin Count | 16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 8 |
| Interface | Parallel |
| Number of Circuits | 1 |
| Max Supply Voltage | 16.5V |
| Min Supply Voltage | 10.8V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Nominal Supply Current | 100nA |
| Power Dissipation | 3mW |
| Max Supply Current | 1μA |
| Throw Configuration | DPST |
| Turn On Delay Time | 230 ns |
| Number of Inputs | 8 |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 130 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 270Ohm Typ |
| High Level Output Current | 20mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 93 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 22pF |
| On-state Resistance Match-Nom | 8.1Ohm |
| Switch Time (Ton, Toff) (Max) | 230ns, 130ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 8.1 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 300ns |
| Drain to Source Resistance | 300Ohm |
| Signal Current-Max | 0.02A |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 1.5mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG508FBRNZ Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. High reliability is provided by advanced packaging method Tube. In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have a ratio of 8:1. Operation at a temperature around -40°C~85°C TA. Total terminations are 16. By its 8 channels, the electronic component provides high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. The electrical component body receives 16 pins. Circuits number 1 make up this analogue multiplexer. Try searching for ADG508 variants of the analog switch ic. A 300Ohm internal resistance characterizes this multiplexer. To find out what the 16 pins do, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. Users shouldn't supply more than 16.5V voltage to the switch device. 10.8V should be the lowest voltage fed to the electronic component. Put voltage above 1μA on the multiplexer to cause damage. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. Integrated with SINGLE-ENDED MULTIPLEXER analog IC. 15V operating voltages can be used with this electrical part. A 8 input needs to be operated. A Drain to Source resistance of 300Ohm is shown for this electronic part.
ADG508FBRNZ Features
8 Channels
Drain-to-Source resistance: 300Ohm
ADG508FBRNZ Applications
There are a lot of Analog Devices Inc. ADG508FBRNZ Analog Switches & Multiplexers ICs applications.
- High-Voltage
- 65 V DACs
- Signal routing between systems
- PCMCIA cards
- Avionics and Military Systems
- Sample-and-hold systems
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- SONET/SDH ADM
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- PBXs
