ADG508FBRWZ-REEL
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 270Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 3.3mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG508 |
| Pin Count | 16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 8 |
| Interface | Parallel |
| Number of Circuits | 1 |
| Max Supply Voltage | 16.5V |
| Min Supply Voltage | 10.8V |
| Operating Supply Current | 100nA |
| Power Dissipation | 3mW |
| Max Supply Current | 1μA |
| Throw Configuration | DPST |
| Turn On Delay Time | 230 ns |
| Logic Function | Multiplexer |
| Number of Inputs | 8 |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 130 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 270Ohm Typ |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 93 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 22pF |
| On-state Resistance Match-Nom | 8.1Ohm |
| Switch Time (Ton, Toff) (Max) | 230ns, 130ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 8.1 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 300ns |
| Signal Current-Max | 0.02A |
| Voltage - Supply, Dual (V±) | ±15V |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG508FBRWZ-REEL Overview
The electrical component comes in 16-SOIC (0.295, 7.50mm Width) packaging, which makes it convenient to ship overseas. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. In Surface Mount, this analog switch is mounted. In the multiplexer and demultiplexer, 8:1 represents the number of circuits. Increasing operating temperature to around -40°C~85°C TA. In total, there are 16 terminations. By its 8 channels, the electronic component provides high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. An electrical component of this type can be found in the 16 series. 1 circuits are used in this analogue multiplexer. Try searching for ADG508 variants of the analog switch ic. An switch multiplexer with 270Ohm internal resistance has a value of 270Ohm. Datasheets for functions of 16 pins are available. Users should never supply a voltage higher than 16.5V to a switch device. A analog switch ic that has a cost-effective Dual supply type. In order for the electronic part to function properly, the lowest voltage should be 10.8V. The switch device would be able to operate with 100nA current. Putting voltage greater than 1μA on the multiplexer may cause damage. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. It can operate from 15V operating voltages. Operating the 8 inputs requires 8 inputs.
ADG508FBRWZ-REEL Features
8 Channels
100nA Supply Current
ADG508FBRWZ-REEL Applications
There are a lot of Analog Devices Inc. ADG508FBRWZ-REEL Analog Switches & Multiplexers ICs applications.
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- RGB switches
- Audio/video switches
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Signal routing between systems
- Audio signal routing
- Cable PC
- E1 Multiplexer
- Modems
- Voice over IP/DSL – Integrated Access Devices, Smart
