ADG509AKP
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 20-LCC (J-Lead) |
| Surface Mount | YES |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 450Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 28mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | J BEND |
| Peak Reflow Temperature (Cel) | 225 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG509 |
| Pin Count | 20 |
| Number of Channels | 1 |
| Interface | Parallel |
| Number of Circuits | 2 |
| Max Supply Voltage | 16.5V |
| Min Supply Voltage | 10.8V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Operating Supply Current | 600μA |
| Nominal Supply Current | 1.5mA |
| Power Dissipation | 27mW |
| Throw Configuration | 4PST |
| Propagation Delay | 300 ns |
| Turn On Delay Time | 400 ns |
| Number of Inputs | 8 |
| Voltage - Supply, Single/Dual (±) | 10.8V~16.5V ±10.8V~16.5V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 400 ns |
| Max Dual Supply Voltage | 16.5V |
| On-State Resistance (Max) | 450Ohm |
| Min Dual Supply Voltage | 10.8V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 11pF |
| On-state Resistance Match-Nom | 22.5Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 300ns, 300ns |
| Charge Injection | 4pC |
| Channel-to-Channel Matching (ΔRon) | 22.5 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Height Seated (Max) | 4.57mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG509AKP Overview
As the electronic part is packed in 20-LCC (J-Lead), international shipping is convenient. In order to provide high reliability, an advanced packaging method Tube is used. In Surface Mount, this analog switch is mounted. Multiplexer and demultiplexer circuits have a number 4:1. Operational temperature extended around -40°C~85°C TA. In total, there have been 20 terminations. Due to its 1 channels, the electrical component produces high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. Into the electrical component body are injected 20 pins. A SP4T switching circuit is used for these analog switches. A 2 circuit is present in this switch device. Try searching for the analog switch ic with ADG509 if you are looking for variants. This digital multiplexer has 450Ohm internal resistance. The functions of 20 pins can be found in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 16.5V to the switch device in normal circumstances. The lowest voltage fed to the electronic component should be 10.8V. 600μA current would be enough for this multiplexer to operate. If put voltage greater than 16.5V on the multiplexer, damage may be caused to the device. The voltage should be at least 10.8V if you are using dual power supplies. An analog IC with the number DIFFERENTIAL MULTIPLEXER is integrated into this board. It is possible to operate 8 inputs.
ADG509AKP Features
1 Channels
Switch Circuit: SP4T
600μA Supply Current
ADG509AKP Applications
There are a lot of Analog Devices Inc. ADG509AKP Analog Switches & Multiplexers ICs applications.
- PBX interfaces
- Automatic test equipment
- High-Voltage
- Avionics
- Precision instrumentation
- Cross Connects
- Medical systems
- PCMCIA cards
- High reliability control systems
- Fiber In The Loop (FITL)
