ADG509AKPZ-REEL
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 20-LCC (J-Lead) |
| Surface Mount | YES |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 450Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | J BEND |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADG509 |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Interface | Parallel |
| Number of Circuits | 2 |
| Max Supply Voltage | 16.5V |
| Min Supply Voltage | 10.8V |
| Operating Supply Current | 600μA |
| Power Dissipation | 27mW |
| Throw Configuration | 4PST |
| Propagation Delay | 300 ns |
| Turn On Delay Time | 450 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 10.8V~16.5V ±10.8V~16.5V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 450 ns |
| Max Dual Supply Voltage | 16.5V |
| On-State Resistance (Max) | 450Ohm |
| Min Dual Supply Voltage | 10.8V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 11pF |
| On-state Resistance Match-Nom | 22.5Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 300ns, 300ns |
| Charge Injection | 4pC |
| Channel-to-Channel Matching (ΔRon) | 22.5 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Height Seated (Max) | 4.57mm |
| Length | 8.965mm |
| Width | 8.965mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG509AKPZ-REEL Overview
Shipping overseas is convenient due to the electrical component's packing in 20-LCC (J-Lead). High reliability is provided by advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a ratio of 4:1. Operation at a temperature around -40°C~85°C TA. The total number of terminations is 20. The electronic part delivers high-quality output through its 1 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. This electrical component is included in the 20 series of products. The analog switch ics are built using SP4T switching circuits. 2 circuits are used in this analogue multiplexer. If you are looking for variants of the digital switch, trying search with ADG509. Internally, this switch multiplexer has a resistance of 450Ohm. You can find the functions of the 20 pins in the datasheets. In normalcircumstances, users should not exceed 16.5V volts for the multiplexer. Dual, Single supply type digital switch with a low cost. The lowest voltage fed to the electronic component should be 10.8V. For this multiplexer to operate, 600μA current would be sufficient. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 16.5V. A dual power supply should have at least 10.8V voltage attached. There is a voltage range of 15V operating voltages for the electrical part.
ADG509AKPZ-REEL Features
1 Channels
Switch Circuit: SP4T
600μA Supply Current
ADG509AKPZ-REEL Applications
There are a lot of Analog Devices Inc. ADG509AKPZ-REEL Analog Switches & Multiplexers ICs applications.
- Access Concentrators
- Signal routing between systems
- Cross Connects
- Microprocessor Controlled Analog Systems
- High-Voltage
- Sample hold systems
- Frame Relay Equipment
- SDH/SONET multiplexers
- Battery-powered systems
- Remote Powered Equipment
