ADG509ATQ
| Parameters | |
|---|---|
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 8 |
| Interface | Parallel |
| Number of Circuits | 2 |
| Max Supply Voltage | 16.5V |
| Min Supply Voltage | 10.8V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Operating Supply Current | 600μA |
| Power Dissipation | 27mW |
| Throw Configuration | 4PST |
| Propagation Delay | 300 ns |
| Turn On Delay Time | 400 ns |
| Voltage - Supply, Single/Dual (±) | 10.8V~16.5V ±10.8V~16.5V |
| Supply Current-Max (Isup) | 1.5mA |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 400 ns |
| Max Dual Supply Voltage | 16.5V |
| On-State Resistance (Max) | 450Ohm |
| Min Dual Supply Voltage | 10.8V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 11pF |
| On-state Resistance Match-Nom | 22.5Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 300ns, 300ns |
| Charge Injection | 4pC |
| Channel-to-Channel Matching (ΔRon) | 22.5 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Length | 19.495mm |
| REACH SVHC | No SVHC |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Mounting Type | Through Hole |
| Package / Case | 16-CDIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 450Ohm |
| Terminal Finish | Tin/Lead (Sn63Pb37) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 28mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | NOT APPLICABLE |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT APPLICABLE |
| Base Part Number | ADG509 |
ADG509ATQ Overview
Packed in 16-CDIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. To ensure high reliability, a new packaging method Tube is used. In Through Hole, you'll find this switch device. 4:1 is the ratio of multiplexer to demultiplexer circuits. An extended operating temperature of -55°C~125°C TA degrees Celsius. A total of 16 terminations have been recorded. The electronic part provides high-quality output because it has 8 channels. An 15V voltage supply should allow the electrical part to be turned on and run. 16 pins are injected to the electronic part body. Circuits based on SP4T switching are used to construct these analog switch ics. There are 2 circuits in this multiplexer. Try searching for ADG509 variants of the analog switch ic. There is 450Ohm internal resistance in this digital multiplexer. Datasheets for functions of 16 pins are available. There is a standard Multiplexer or Switches analogue multiplexer here. It is generally not recommended to supply a voltage higher than 16.5V to the switch device in normal circumstances. 10.8V should be the lowest voltage fed to the electronic component. An operating current of 600μA would be sufficient for this switch device. Despite this switch device's dual supply capability, its voltage should not exceed 16.5V. A dual power supply should have at least 10.8V voltage attached. Integrated with an analog IC DIFFERENTIAL MULTIPLEXER.
ADG509ATQ Features
8 Channels
Switch Circuit: SP4T
600μA Supply Current
ADG509ATQ Applications
There are a lot of Analog Devices Inc. ADG509ATQ Analog Switches & Multiplexers ICs applications.
- DVD-R
- New designs requiring multiplexer functions
- Frame Relay Equipment
- Relay replacements
- PBX interfaces
- 65 V DACs
- Cross Connects
- Communications systems
- PDH Multiplexers
- RGB switches
