ADG509FBRN
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 270Ohm |
| Additional Feature | ACTIVE OVERVOLTAGE PROTECTION |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 3.3mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG509 |
| Pin Count | 16 |
| Number of Channels | 1 |
| Interface | Parallel |
| Number of Circuits | 2 |
| Max Supply Voltage | 15V |
| Min Supply Voltage | -15V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Power Dissipation | 3mW |
| Max Supply Current | 1μA |
| Throw Configuration | 4PST |
| Turn On Delay Time | 230 ns |
| Number of Inputs | 8 |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 130 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 270Ohm Typ |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 93 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 12pF |
| On-state Resistance Match-Nom | 8.1Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 230ns, 130ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 8.1 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 300ns |
| Voltage - Supply, Dual (V±) | ±15V |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG509FBRN Overview
Shipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). High reliability is ensured by the advanced packaging method Tube. In Surface Mount, you'll find this switch device. 4:1 is the ratio of multiplexer to demultiplexer circuits. Increasing operating temperature to around -40°C~85°C TA. Total terminations are 16. High-quality output is provided by the electronic component's 1 channels. When the electronic component is given a voltage of 15V, it should be turned on and run. There is an electrical component included in the 16 series. A SP4T switching circuit is used for these analog switches. A total of 2 circuits make up this switch device. Use ADG509 to search for variants of the digital switches. It has an internal resistance of 270Ohm. For details about the functions of 16 pins, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 15V in normal situations. A low voltage of -15V should be applied to the electronic component. Put voltage above 1μA on the multiplexer to cause damage. For this switch, a dual supply voltage is feasible, but it must not exceed 22VWith a DIFFERENTIAL MULTIPLEXER analog IC integrated into the board. There are 8 inputs to be operated. Check out the electrical component's additional features, such as the following: ACTIVE OVERVOLTAGE PROTECTION.
ADG509FBRN Features
1 Channels
Switch Circuit: SP4T
Additional Features: ACTIVE OVERVOLTAGE PROTECTION
ADG509FBRN Applications
There are a lot of Analog Devices Inc. ADG509FBRN Analog Switches & Multiplexers ICs applications.
- Remote Powered Equipment
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Avionics and Military Systems
- Medical Instrumentation
- DSLAMs
- Fiber In The Loop (FITL)
- Voice over IP/DSL – Integrated Access Devices, Smart
- Multi-Line E1 Interface Cards
- Cable Modem
- Fault Tolerant Systems
