ADG511BN
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 30Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | ADG511 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Channels | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Power Dissipation | 470mW |
| Throw Configuration | SPST |
| Voltage - Supply, Single/Dual (±) | 3V~5.5V ±4.5V~5.5V |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Max Dual Supply Voltage | 5.5V |
| On-State Resistance (Max) | 30Ohm Typ |
| Min Dual Supply Voltage | 4.5V |
| Screening Level | MIL-STD-883 |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 200ns, 120ns (Typ) |
| Charge Injection | 11pC |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 375ns |
| Switch-off Time-Max | 150ns |
| Normal Position | NC |
| Height Seated (Max) | 5.33mm |
| Length | 20.13mm |
| Width | 7.62mm |
| RoHS Status | Non-RoHS Compliant |
ADG511BN Overview
Packed in 16-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. High reliability is achieved by using advanced packaging method Tube. The multiplexer is located in Through Hole. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operational temperature extended around -40°C~85°C TA. There are 16 terminations totally. The electronic part provides high-quality output because it has 4 channels. If the voltage supply is 5V volts, the electrical component should be turned on and run. 16 pins are injected to the electronic part body. Circuits based on SPST - NC switching are used to construct these analog switch ics. Using the ADG511 search parameter, you can discover variants of the switch. In this multiplexer, the internal resistance is 30Ohm. Please refer to the datasheets for 16 pins functions. The analog multiplexer shown here is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. 4.5V is the lowest voltage the electrical component should receive. Despite this switch's dual supply capability, its voltage should not exceed 5.5V. In the case of dual power supplies, you should connect at least 4.5V. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. This electrical part is compatible with 5V operating voltages.
ADG511BN Features
4 Channels
Switch Circuit: SPST - NC
ADG511BN Applications
There are a lot of Analog Devices Inc. ADG511BN Analog Switches & Multiplexers ICs applications.
- Data Acquisition Systems
- ISDN NT1/TA
- T1/E1 Terminals
- Power routing
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Access Concentrators
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- SONET/SDH ADM
- Avionics
- Communication systems
