Parameters |
Peak Reflow Temperature (Cel) |
235 |
Number of Functions |
4 |
Supply Voltage |
5V |
Terminal Pitch |
1.27mm |
Reach Compliance Code |
not_compliant |
Time@Peak Reflow Temperature-Max (s) |
20 |
Base Part Number |
ADG511 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Number of Channels |
4 |
Interface |
Parallel |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
4.5V |
Power Dissipation |
10μW |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
375 ns |
Voltage - Supply, Single/Dual (±) |
3V~5.5V ±4.5V~5.5V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
150 ns |
Max Dual Supply Voltage |
5.5V |
On-State Resistance (Max) |
30Ohm Typ |
Min Dual Supply Voltage |
4.5V |
Screening Level |
MIL-STD-883 |
Dual Supply Voltage |
5V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
68 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
9pF 9pF |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
200ns, 120ns (Typ) |
Charge Injection |
11pC |
Crosstalk |
-85dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Normal Position |
NC |
Height Seated (Max) |
1.75mm |
Length |
9.9mm |
Width |
3.9mm |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Surface Mount |
YES |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
30Ohm |
Terminal Finish |
Tin/Lead (Sn85Pb15) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
10μW |
Technology |
CMOS |
Terminal Form |
GULL WING |
ADG511BR Overview
Packed in 16-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. High reliability is achieved by using advanced packaging method Tube. There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. In total, 16 terminations have occurred. The electronic part provides high-quality output because it has 4 channels. When the electronic component is given a voltage of 5V, it should be turned on and run. 16 pins are injected to the electronic part body. Unlike digital switches, these are based on SPST - NC switching circuits. Try searching with ADG511 to find analog multiplexer variants. The internal resistance of this digital multiplexer is 30Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. A voltage higher than 5.5V should not normally be supplied to the switches. The digital multiplexer has a low cost Dual, Single supply. A low voltage of 4.5V should be applied to the electronic component. When the digital multiplexer is charged above 1μA, damage can occur. Despite this switch device's dual supply capability, its voltage should not exceed 5.5V. If you are using dual power supplies, you should attach at least 4.5V. There are SEPARATE OUTPUT outputs on this analog switch ic.
ADG511BR Features
4 Channels
Switch Circuit: SPST - NC
ADG511BR Applications
There are a lot of Analog Devices Inc. ADG511BR Analog Switches & Multiplexers ICs applications.
- Avionics test equipment
- High speed data transmission line cards
- Data switching
- Video switching
- E1 Network Equipment
- Microprocessor controlled systems
- Digital cross connects (DSX-1)
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- RGB switches
- Digital Cross-Connects