ADG511BR-REEL
| Parameters | |
|---|---|
| Charge Injection | 11pC |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 375ns |
| Switch-off Time-Max | 150ns |
| Normal Position | NC |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| RoHS Status | Non-RoHS Compliant |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 30Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG511 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Channels | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Power Dissipation | 600mW |
| Throw Configuration | SPST |
| Voltage - Supply, Single/Dual (±) | 3V~5.5V ±4.5V~5.5V |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Max Dual Supply Voltage | 5.5V |
| On-State Resistance (Max) | 30Ohm Typ |
| Min Dual Supply Voltage | 4.5V |
| Screening Level | MIL-STD-883 |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 200ns, 120ns (Typ) |
ADG511BR-REEL Overview
Shipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.154, 3.90mm Width). High reliability is provided by advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. 1:1 is the ratio between multiplexers and demultiplexers. Increasing operating temperature to around -40°C~85°C TA. 16 terminations have been made so far. A high-quality output is provided by the electrical component's 4 channels. When a voltage supply of 5V is used, the electronic component should be turned on and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. Based on SPST - NC switching circuits, these analog multiplexers work. Try searching for ADG511 variants of the analog switch ic. Analog switches have 30Ohm internal resistance. For details about the functions of 16 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. The lowest voltage the electronic part should receive is 4.5V. If put voltage greater than 5.5V on the multiplexer, damage may be caused to the device. The voltage should be at least 4.5V if you are using dual power supplies. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. This electrical part is compatible with 5V operating voltages.
ADG511BR-REEL Features
4 Channels
Switch Circuit: SPST - NC
ADG511BR-REEL Applications
There are a lot of Analog Devices Inc. ADG511BR-REEL Analog Switches & Multiplexers ICs applications.
- Microprocessor Controlled Analog Systems
- RGB switches
- Relay replacements
- Communication systems
- Industrial control systems
- DSLAMs
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Wireless Local Loop
- ISDN NT1/TA
- DSUs
