ADG511BR-REEL7
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 30Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 10μW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG511 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 4 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 100pA |
| Power Dissipation | 10μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 375 ns |
| Voltage - Supply, Single/Dual (±) | 3V~5.5V ±4.5V~5.5V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 5.5V |
| On-State Resistance (Max) | 30Ohm Typ |
| Min Dual Supply Voltage | 4.5V |
| Screening Level | MIL-STD-883 |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 200ns, 120ns (Typ) |
| Charge Injection | 11pC |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG511BR-REEL7 Overview
Packed in 16-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. Surface Mount is where this multiplexer is located. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Temperatures around -40°C~85°C TA are extended for operation. Total terminations are 16. As a result of its 4 channels, this electronic component provides high-quality output. With a 5V voltage supply, the electrical component should be turned on and run. An electrical component of this type can be found in the 16 series. Unlike digital switches, these are based on SPST - NC switching circuits. If you are looking for variants of the digital switch, trying search with ADG511. An switch multiplexer with 30Ohm internal resistance has a value of 30Ohm. You can find the functions of the 16 pins in the datasheets. It is a typical Multiplexer or Switches analog multiplexer. Users should never supply a voltage higher than 5.5V to a switch device. Analog switch ics with Dual, Single supply type are cost-effective. 4.5V is the lowest voltage the electrical component should receive. For this digital switch to work, 100pA current would suffice. Put voltage above 1μA on the multiplexer to cause damage. For this multiplexer, dual supply voltage is feasible, but it should not exceed 5.5V. When using dual power supplies, you should attach at least 4.5V. SEPARATE OUTPUT outputs are utilized by this digital multiplexer.
ADG511BR-REEL7 Features
4 Channels
Switch Circuit: SPST - NC
100pA Supply Current
ADG511BR-REEL7 Applications
There are a lot of Analog Devices Inc. ADG511BR-REEL7 Analog Switches & Multiplexers ICs applications.
- Power routing
- E1 Network Equipment
- Frame Relay Equipment
- Avionics test equipment
- Remote Powered Equipment
- Modems
- Avionics
- Fiber In The Loop (FITL)
- Microprocessor Controlled Analog Systems
- Multi-Line E1 Interface Cards
