Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 2 weeks ago) |
Contact Plating |
Tin |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Surface Mount |
YES |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
30Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
10μW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
5V |
Terminal Pitch |
1.27mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG512 |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Operating Supply Voltage |
5V |
Polarity |
Non-Inverting |
Number of Channels |
4 |
Interface |
Parallel |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
4.5V |
Operating Supply Current |
100pA |
Power Dissipation |
10μW |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
375 ns |
Voltage - Supply, Single/Dual (±) |
3V~5.5V ±4.5V~5.5V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
150 ns |
Max Dual Supply Voltage |
5.5V |
On-State Resistance (Max) |
30Ohm Typ |
Min Dual Supply Voltage |
4.5V |
High Level Output Current |
30mA |
Dual Supply Voltage |
5V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
68 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
9pF 9pF |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
200ns, 120ns (Typ) |
Charge Injection |
11pC |
Crosstalk |
-85dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Normal Position |
NO |
Height Seated (Max) |
1.75mm |
Length |
9.9mm |
Width |
3.9mm |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG512BRZ-REEL Overview
Shipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). The advanced packaging method Tape & Reel (TR) provides high reliability. A switch device like this is mounted in Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Around -40°C~85°C TA is the extended operating temperature. Total terminations are 16. Due to its 4 channels, the electrical component produces high-quality output. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. The electronic part body is injected with 16 pins. Based on SPST - NO switching circuits, these analog multiplexers work. Try searching for ADG512 variants of the analog switch ic. As far as internal resistance is concerned, it has 30Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. A voltage higher than 5.5V should not normally be supplied to the switches. Analogue multiplexers of the Dual, Single supply type that are cost-effective. 4.5V should be the lowest voltage fed to the electronic component. For this multiplexer to operate, 100pA current would be sufficient. Putting voltage greater than 1μA on the multiplexer may cause damage. If put voltage greater than 5.5V on the multiplexer, damage may be caused to the device. The voltage should be at least 4.5V if you are using dual power supplies. A voltage of 5V can be used to operate the electronic component.
ADG512BRZ-REEL Features
4 Channels
Switch Circuit: SPST - NO
100pA Supply Current
ADG512BRZ-REEL Applications
There are a lot of Analog Devices Inc. ADG512BRZ-REEL Analog Switches & Multiplexers ICs applications.
- Video signal routing
- Multiplexers
- Switching Systems
- Fault Tolerant Systems
- Battery Powered Instruments
- ISDN NT1/TA
- SDH/SONET multiplexers
- Video switching
- Avionics test equipment
- Public switching systems