ADG512TQ
| Parameters | |
|---|---|
| Contact Plating | Lead, Tin |
| Mounting Type | Through Hole |
| Package / Case | 16-CDIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 30Ohm |
| Terminal Finish | Tin/Lead (Sn63Pb37) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 10μW |
| Technology | CMOS |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Base Part Number | ADG512 |
| Pin Count | 16 |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 3V |
| Power Dissipation | 10μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 375 ns |
| Voltage - Supply, Single/Dual (±) | 3V~5.5V ±4.5V~5.5V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 5.5V |
| On-State Resistance (Max) | 30Ohm Typ |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 200ns, 120ns (Typ) |
| Charge Injection | 11pC |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Height Seated (Max) | 5.08mm |
| Length | 19.05mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG512TQ Overview
Due to its 16-CDIP (0.300, 7.62mm) packaging, the electronic part is convenient for international shipping. The advanced packaging method Tube provides high reliability. There is an analog multiplexer mounted in position Through Hole. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operational temperature extended around -55°C~125°C TA. Totally, there are 16 terminations. By its 1 channels, the electronic component provides high-quality output. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. A total of 16 pins are injected into the body of the electronic part. Unlike digital switches, these are based on SPST - NO switching circuits. It consists of 4 circuits. ADG512 can be used to search for analog multiplexer variants. It has an internal resistance of 30Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. Multiplexer or Switches is a typical switch device. A voltage higher than 5.5V should not normally be supplied to the switches. A analog switch ic that has a cost-effective Dual, Single supply type. 3V is the lowest voltage that should be fed to the electronic electronic part. It may damage the digital multiplexer if the voltage is higher than 1μA. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 5.5V. If you are using dual power supplies, you should attach at least 4.5V.
ADG512TQ Features
1 Channels
Switch Circuit: SPST - NO
ADG512TQ Applications
There are a lot of Analog Devices Inc. ADG512TQ Analog Switches & Multiplexers ICs applications.
- Audio and video switching
- Industrial control systems
- Optical Applications
- Audio/video switches
- Automotive applications
- Transmit
- Digital access cross connects
- Cable PC
- Private Branch Exchange (PBX)
- T1/E1 Terminals
